sam's club/chris lilly signature smoker

[RichardF]

anybody see one of these in person either when they were in huntsville or now in bentonville? thoughts?

 

[landarc]

No, how much? That looks pretty cool.

 

[J-Rod]

That looks like a really nice unit! I'd like to see one in person.

 

[deguerre]

Looks like some pretty sloppy welding in the lid. Made in China? Ah. From the Facebook page: $998.00 is the price at Sam's Club...

 

[Bludawg]

Looks like a Fat cousin to an ABS Bar-B- Cube with less usable space.

 

[deguerre]

A couple more pics.

 

[Big Country BBQ]

looks like a fancy yard ornament!!

 

[deguerre]

Looks like a Fat cousin to an ABS Bar-B- Cube with less usable space.

At only a couple hundred dollars more, the ABS looks to be a better buy, at least just comparing pics anyway...

 

[RichardF]

i guess no one has seen one in the wild or at the sam's club in bentonville. looks kinda interesting, sorta like a smaller version of what's mouned on the big bob gibson trailer. as this was a limited run to see if there was any interest in warrent a prodction run, i figured they'd have been fabricated somewhere in teh USA.

 

[Smokeat]

What is behind that skinny 2 handled door that is not open in the pics, a water pan? I'm flummoxed. I also like that it looks like the lower portion and doors are double walled.

 

[dwfisk]

Can't tell for sure but it looks like 11 gage (1/8") or better steel with some good angle iron and tubing structure. If it really is that heavy it might be a pretty good cooker, pretty durn pricey though.

 

[oldbill]

Check this one out, it's more expensive but it looks a little bigger and a lot more versatile! http://www.lonestargrillz.com/Square-Smokers---Grills.html

 

[SoHappy]

Looks to me like the "skinny door" is a fixed panel with damper controls for heat and smoke going into the upper chambers.

 

[CraigC]

If I'm going to spend $998.00 for a no doubt chinese junk (not to be confused with the boat, but any non food product they export to the US), I'm going a couple hundred more for a new Lang 36.

 

[Hawg Father of Seoul]

Saw them the other day. Had two 18 pound briskets in hand and it did not look like the quality was there so I just kept trucking.

 

[KBird]

I saw one at the Sams in Bentonville. Impressed by the heavy duty steel they used, and you have lots of options for raising and lowering the charcoal. Didn't study it alot, but it nice to see manufacturers stepping up the quality. This one looks like it is built to last.:eusa_clap

 

[ButtBurner]

always nice to see new smoker products.

I try to keep an open mind, I think its kinda cool.

Insteresting design

 

[dobdabomb]

I honestly did not see it being worth the cost they are asking thats for sure. I was not that impressed when I went to see them here in Huntsville.

 

[fuzzymusket]

It's funny I just bought a somewhat similar setup from Sam's. Here's the link to my post and some pics:

http://www.bbq-brethren.com/forum/showthread.php?t=165636

It's not exactly the same thing, that one looks to be setup solely for grilling\smoking with lump charcoal where mine has a LP side and an offset smoker.

The biggest difference is price!! Mine was only $349. I can say that I wish the metal was a little thicker. It's not bad but for long term durability I'd prefer a little thicker. And yes it's made in china.

Based on the setup I just bought, and my overall experience with Sam's, I'd say that if you're a somewhat gifted amateur like me, it'd probably work fine for your backyard BBQ but I would look elsewhere for competition. Especially at that price point. If it were $400 cheaper then sure.

 

[RichardF]

now that these have been out in the wild for the summer has anybody had the chance to play with one?