Our Homepage | Donation to Forum Overhead | Welocme | Merchandise | Associations | Purchase Subscription | Amazon Affiliate |
|
Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking. |
|
Thread Tools |
03-11-2009, 10:43 PM | #1 |
somebody shut me the fark up.
Join Date: 10-12-08
Location: Gallatin, TN
Name/Nickname : Richard
|
Getting Ready To Finish My UDS - A Few Questions Regarding Paint & Finish
I've pretty much read the entire LONG Thread, as well as Norco's. I have a great charcoal basket etc, all parts, so now it really comes down to getting it painted. After a good burnout, I wire brushed the drum, then used high heat BBQ paint as primer as prep for the final paint job and to keep it from rusting. Not so sure I should have done this, as the paint seems to not be sticking at all. I think I need to do a lot more wire brushing or use something else as primer, or BOTH.
So my questions are: When you wire brush the outside of the drum, does it need to show bare metal 100%? After my first go around, I had all the rust and remaining paint off, and thought this would be more than adequate to create a "sticky" surface for the paint to adhere to. Apparently not! What kind of paint should I use, and should I use primer? I plan on using a glossy red as my paint, so does that need to be high heat resistant engine paint, or can I use plain automotive paint? Feedback will be greatly appreciated, and thanks to all the pioneers on this board who inspired me to get myself into this mess!
__________________
Moose Showcase Your Cooking in the BBQ Brethren Throwdowns! 2017's "Mayo Explosion" The 2022 Steak Cooking Controversy: Follow the Science! Check out my blog: www.mooseonfire.com |
|
03-11-2009, 10:57 PM | #2 |
somebody shut me the fark up.
Join Date: 07-11-06
Location: Norco, Ca.
|
Scuff it up and use Engine paint. Regular paint is ok and will work but engine paint is better for when your in awe of the goods and leave the lid off longer than you should.
|
|
03-11-2009, 11:37 PM | #3 | |
is one Smokin' Farker
Join Date: 10-25-08
Location: Drippin' Springs, TX
|
Moose, I started on the outside of my new drum yesterday with the intention
of taking it down to bare metal. I dunno what they used for paint and primer but it was very hard! After 30 minutes I had made almost no progress. Switched to Plan B, no sense in creating extra work so I just scuffed the existing paint with 60 grit and then 180 grit. Made for a pretty nice surface with good tooth for the paint. Norco is correct, use engine paint, it is only good for 500* but that should be fine. I decided to go with your basic Krylon primer and paint just to see if that is good enough. I think it will work and if it doesn't, I'll wish that I had taken Pat's advice. Weiser PS: Mine is also going to be Red. Quote:
__________________
[COLOR=Red][I]"There is a Fine Line between a Hobby and a Mental Disorder." [/I][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR][COLOR=Red][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR] |
|
|
03-12-2009, 05:22 AM | #4 |
Knows what a fatty is.
Join Date: 01-27-09
Location: porter, in
|
I never primed mine just engine paint, i also went down to bare metal.
__________________
CG SP w/SFB rotis,Weber 18.5 & 22.5, UDSx3-Their not just drums, their quality cookin devices |
|
03-12-2009, 07:26 AM | #5 |
is one Smokin' Farker
Join Date: 01-22-08
Location: waterloo ontario
|
Your problem may be related to what was in and where the barrel has been. You need to use a "body shop wash" to remove any grease or silicone that you are trying to paint over. If you had a clean surface the paint would stick.
|
|
03-12-2009, 09:10 AM | #6 | |
Babbling Farker
Join Date: 08-03-08
Location: Mesa, AZ Not exactly hell, but the zip code is very close...
|
Quote:
Also, did you make sure there was no sanding dust left on the to be painted surface???
__________________
[FONT=Comic Sans MS]Bo Compton in Mesa, AZ, KCBS CBJ[/FONT] [FONT=Comic Sans MS]Weber Ranch Kettle, BDS Mega, OTS x 2, Weber Platinum[/FONT] [FONT=Comic Sans MS]18.5 WSM w/Stacker from ProQ, 22.5 WSM, Reverse Flow Lang Clone 80 butt capacity mounted on 25 foot trailer with attached awnings[/FONT] [FONT=Comic Sans MS][COLOR=#ff0000]LFSA RED Thermapen,[/COLOR] [/FONT] [FONT=Comic Sans MS]And 1 2010 Victor brand Hot Dog Cart[/FONT] |
|
|
03-12-2009, 10:52 AM | #7 | |
is one Smokin' Farker
Join Date: 10-25-08
Location: Drippin' Springs, TX
|
"Your problem may be related to what was in and where the barrel has been. You need to use a "body shop wash" to remove any grease or silicone that you are trying to paint over. If you had a clean surface the paint would stick." Good point. I wipe the surface with either Prep-Solv or Lacquer Thinner before applying any paint. There is a good amount of oil in your fingure tips too which will cause problems. Quote:
Weiser
__________________
[COLOR=Red][I]"There is a Fine Line between a Hobby and a Mental Disorder." [/I][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR][COLOR=Red][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR] |
|
|
03-12-2009, 02:46 PM | #8 |
somebody shut me the fark up.
Join Date: 08-13-03
Location: St. Peters MO: 38.786730,-90.642551
Name/Nickname : Mark
|
For the record; I used "high temp" engine spray paint for my biohazard logo and managed to burn it. Not that I give a $hit. Just give it some more character.
__________________
Dr. Mark (STL) Ph.D. (honorary) Bovine $hitology A thin line separates paranoia from an acute understanding of reality. |
|
03-12-2009, 05:55 PM | #9 |
Full Fledged Farker
Join Date: 11-30-08
Location: Northwest NJ
|
I used regular Krylon, not the high heat type and mine is fine. But like Norco said I have never left the lid off (yet) and had the temp spike on me. If you want the extra heat insurance go with engine paint. I didn't because I did not see the color I wanted in engine paint, so I will have to be careful. Probably just jinxed myself now.
I don't think I would use primer, unless you can find a high heat primer. I don't know what temp rattlecan primers are rated up to, but I would assume it is the same as regular paint. If you clean and scuff the drum properly there really is no need for primer. But thats just my opinion and I could be wrong. I have used regular Krylon paint on engine blocks and it holds up very well. Water-cooled V-8s do not get very hot in paint terms. Yes, they are too hot to touch, but if your cooling system is working fine they should never get hot hot enough to burn your paint.
__________________
[FONT=Tahoma][SIZE=3][SIZE=2] [SIZE=3][SIZE=2]Wood fired pizza oven,Copper Weber Gold, Green Weber Performer, Black Weber Silver, Green logo'd 18 inch Weber Gold, and a UDS of course. [/SIZE] [/SIZE][/SIZE] [/SIZE][/FONT] [SIZE=3][URL]http://cookinginmyyard.com/[/URL][/SIZE] |
|
03-12-2009, 11:43 PM | #10 |
is one Smokin' Farker
Join Date: 10-25-08
Location: Drippin' Springs, TX
|
That was pretty much my frame of reference too.
Regular old Krylon works well on blocks and intakes. The engine paint and primer are rated at 500* I don't ever plan on letting the UDS go above 375* Lawn furniture down here gets hotter than that in the Summer. Weiser
__________________
[COLOR=Red][I]"There is a Fine Line between a Hobby and a Mental Disorder." [/I][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR][COLOR=Red][SIZE=1][COLOR=Black] [/COLOR][/SIZE][/COLOR] |
|
03-13-2009, 12:30 AM | #11 |
is One Chatty Farker
Join Date: 11-07-07
Location: Middletown California
|
I did not plan on letting mine get above 375 either, but sh*t happens!!!
The high temp. bbq paint base held up fine, but the red top coat did not.
__________________
Cheers, Jerry aka Barbarian Drumhead - UDS x 2 & UDG Thermopen Keep on Smokin' KC native missin' KC IMBAS Certified MOINK Baller 2009 I also support PETA - People Eating Tasty Animals |
|
03-13-2009, 08:47 AM | #12 | |
Full Fledged Farker
Join Date: 11-30-08
Location: Northwest NJ
|
Quote:
Nice. And remind me, how long is summer in Texas? 9 months?
__________________
[FONT=Tahoma][SIZE=3][SIZE=2] [SIZE=3][SIZE=2]Wood fired pizza oven,Copper Weber Gold, Green Weber Performer, Black Weber Silver, Green logo'd 18 inch Weber Gold, and a UDS of course. [/SIZE] [/SIZE][/SIZE] [/SIZE][/FONT] [SIZE=3][URL]http://cookinginmyyard.com/[/URL][/SIZE] |
|
|
03-13-2009, 02:04 PM | #13 |
Take a breath!
Join Date: 04-28-08
Location: Carvel, AB Canada
|
I used high temp enamel (600F). I burned the paint off the outside and the touched it up a bit with a sander. I cleaned the surface with a rag soaked with paint thinner (as a degreaser and tack rag) before spraying on two light coats.
__________________
UDS Stumps Clone |
|
03-13-2009, 04:01 PM | #14 |
On the road to being a farker
Join Date: 11-11-08
Location: Glendale, AZ by way of Pittsburgh, Pa
|
Left mine with the original black. Hasn't burned or rusted, yet.
__________________
I have a fever, and the only prescription is, more cowbell!:twisted: UDS Weber gasser Brinkman gas smoker Weber Kettle |
|
03-13-2009, 06:08 PM | #15 |
Quintessential Chatty Farker
Join Date: 12-15-07
Location: England
|
My mini is original black and the UDS recieven no sanding after the burm, just a wipe down with a ditry rag, some primer and black paint. No problems so far even the vinal sticker is holding strong.
__________________
www.drsweetsmoke.com Slappin that bass like some delerious funky preist!!! UDS, Half Pint (Mini UDS), Weber, ProQ 20, Kegrilla *250 gallon cooker- 'The Meat Beast!!'* British BBQ Championships Grand Champion 2008 ~~~~ British BBQ Society - Southern Championship Grand Champions 2009
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
trigg finish | DevineSwine | Q-talk | 7 | 03-22-2011 06:46 PM |
Opinions Of this Finish? | Jeff S. | Competition BBQ | 7 | 06-02-2010 11:24 PM |
UDS Finish & Broken In (with prons) | BamaRambler | Q-talk | 25 | 10-15-2009 09:32 AM |
Just finish reading the UDS thread.... | GridironGriller2 | Q-talk | 16 | 11-11-2008 06:42 PM |
Thread Tools | |
|
|