|
Used for the first time last Friday. Seasoned the smoker the week prior. Did pork spare ribs and chicken quarters.
Didn't hold heat as long as I would have liked. Had to add charcoal halfway through the cook. I think I didn't put enough in to begin with. Have to learn sometime. Ribs and chicken turned out perfect after all was said and done. Now I just have to clean the outside and paint it. http://inlinethumb44.webshots.com/18...600x600Q85.jpg |
Quote:
http://www.mcmaster.com/#cad-2d/1889a22/ This is the latch that popped into my mind when I considered the idea of doing a detachable bottom. -Rodney |
Has anyone used JB Weld on their UDS cooker? :redface:
|
Quote:
-Rodney |
Quote:
What are you trying to do with the JB Weld? |
Quote:
|
Quote:
Just load that basket up so you don't have to worry. Reuse what you don't burn the next time. These burn so long there would be no reason to worry about running out. JMHO........... Paul B SS UDS SS Auspit |
Thank you everyone for sharing your experiences on your builds. Lots of information in this thread! I am at about page 210 but have throttled back on my reading cause there is a lot of repeat info and I had the info I needed to build mine last night.
There was only 1 tool broken and 2 injurys during this adventure. We bought a nibbler (to cut out the bottom) and broke the tip on it. Then I burnt my finger after I grabbed the side right after doing some grinding. I thought it was gonna blister up but it is fine today. My buddy must have gotten a piece of porcelien in his eye cause his eyes were giving him problems today and ended up going to the ER to get a sliver taken out of it. As far as the construction goes, I wanted to use the Weber lid so I had to cut out the bottom for it to fit rights, then use the top of the drum as the bottom. I sealed it with some foil inside the lip. I decided to use the bottom of the Weber Kettle as my ash tray by cutting the kettle a few inches above where the grate sits without the factory welded tabs. We also drilled several 3/4" holes around the parameter for better air flow. All in all, the assembly went pretty good and I bought some new tools that I needed anyway. For inlets, I drilled 4 sets of double 3/4" holes with flaps to cover them made out of stainless I didn't take any pics during assembly because I have a hard time remembering to but I will take some pics after I paint it later. I put the finishing touches on this afternoon and lathered some lard on the inside before I lit it up. I was a little worried about airflow using the cut-up kettle base but as soon as I put a 1/2 chimney of ashed briquettes in, it was only a matter of minutes before it hit 350. I closed off 3 vents and left the fourth cracked just a scosh before my temps finally dropped to 275 and held there. I probably have some leaks. It is 10:30pm and I am off to prep some fattys to throw on for a very late night snack! |
Pics or it didn't happen!
|
I'm gonna blame my hole-saw (which I will never buy again, Unibit all the way) and say that the hole was too large for the pipe nipple and I didn't want to go and buy another barrell so I continued with the project.
While finishing I had the thought to use JB Weld to seal the nipple to the barrel, it worked perfectly during the seasoning process, I just wanted to find out if i'm going to run into any issues. |
Quote:
http://www.jbweld.net/faq.php -Rodney |
I put together a "how I built my charcoal basket" video and posted it in a new thread if anyone's interested.
http://www.bbq-brethren.com/forum/sh....php?p=1224095 -Rodney |
Heres how you get rid of the dreaded liner.
Yes, thats a leaf blower, and yes, the fire dept. responded. http://img265.imageshack.us/img265/8555/hhrrrrrg006.jpg |
Quote:
|
Quote:
Too much will melt the barrel. |
All times are GMT -5. The time now is 08:07 PM. |
|
Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.