|
Quote:
I replaced them with a couple of smokey joe thermometers from cabelas. They were about $15 each. Good for a quick glance at the temp. I mainly used the ET-732. |
To get any burn out, you need to drill your draft holes. To get a really good burn out - force draft air into them. I think in the first mother of all UDS threads - a person hooked up a vent hole to his shop vac's exhaust. Pretty sure he glowed his drum.
|
Quote:
|
Thanks to this thread, I finished up my smoker last weekend. Its not too Ugly, but it will do! Made some wings earlier in the week, just waiting on a free weekend to do something more substantial.
http://www.bbq-brethren.com/forum/at...1&d=1318639845 |
My old man always said measure twice cut once. In this case, I need to ask twice BEFORE I drill once. I'm using four 3/4 inch air inlets which will be three with caps and one with a ball valve. I measured the out diameter of the threaded pipe and it is one inch in diameter. From what I've read, I should use a 7/8 step drill bit to drill the holes in my drum for the 3/4 inch pipe to thread into it. Can someone please tell me if this is correct. I've bought all my threaded pipe and pipe caps in 3/4 inch. if I need to exchange it for something smaller, I would rather do it before I drill any holes. Thanks in advance.
|
You need a 1" hole for the 3/4 pipe nipples. I used a hole saw for mine and the nipples fit tight. I backed them up with conduit nuts one inside, one outside.
|
I used a 1" drill bit that looked like a giant regular bit. I couldn't afford to pay $50 bucks for a 1" step drill bit. Would have been nice, but thats a lot of cash. The big cartoon looking bit was $11. It got the job done.
|
For those that have the side air intake pipe, what are your pipes made of? I found a perfect sized pipe today for mine but it's galvanised. As it's actually outside the drum it shouldn't really matter, should it???
|
Also, what size basket does everyone have?
|
It would be fine. It's only job is air flow.
|
Quote:
I couldn't find the hole size for 1" nipples on here so just wanted to make available to the group (went through a couple of $12 bits prior to finding the right size lol). God bless, Disciple |
Well it's finished......
Pics will be posted tomorrow when I can get the camera back from the gf. Did a small test run this afternoon to test for leaks and to set the paint.......Looks GREAT!!!!! So far everything has been on the money. Just wanted to say Thanks to the brethren and the site for getting me where I am today. |
After trying a weed burner, Easy-Off, and three different paint strippers on the dreaded red liner, I did a burn this weekend with two pallets and a leaf blower. I just set the blower about two inches from each intake hole for about 15 minutes. Eight-foot flames out the top! I wouldn't try this in town. The next day the liner came out with just a light scrubbing with a scouring pad and water. Maybe this will help someone else who is stuck with a lined drum. I would have moved on to an unlined drum by now but 30 gallon drums are hard to find around here. Looks like it's going to make a nice mini-smoker for the bi-annual trips to Bristol Motor Speedway. I'm using a 16-quart stainless mixing bowl for a top. Will post photos next week.
|
http://i208.photobucket.com/albums/b...2/IMG_1265.jpghttp://i208.photobucket.com/albums/b...2/IMG_1267.jpghttp://i208.photobucket.com/albums/b...2/IMG_1269.jpg
This is a burn out I did last week. The opening is for the BGEE sliding door. There was not any liner it's a S/S drum that held Teatree Oil. I used a leaf blower to get it going, but it didn't need any help. It was windy that day and it was a roaring flame. Now I just need to reassemble it and get cooking. Damn my lawn looks green too!!! |
Quote:
Some here will say "better safe than sorry", but especially since zinc vapors are only a hazard if you inhale them, and a significant quantity of them at that, it's kind of a stretch. FYI, some people here use a PVC pipe as a smoke stack, and that works fine. When smoking at 225, I can literally lift the lid off of the smoker with my bare hands, especially if I use my 2" galvanized pipe smoke stack as a handle. That should give you an idea of how hot the smoke stack (doesn't) get during use. -Rodney |
All times are GMT -5. The time now is 05:51 PM. |
|
Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.