|
Quote:
|
Quote:
|
Honestly I can not recall what I used to remove the bung holes on mine - only that it was a non-issue. I think I used a vice grip and just opened it up and turned it - the bung hole is threaded. That said, I might have used a screwdriver to do the same thing.
I then screwed in a close nipple of the same thread for a short smoke stack. -- Mine was well oiled (coconut oil barrel) and did not take a huge amount of torque to open. |
O.k. I've read all the pages, got a drum, built a smoker, cooked on it a dozen times. The only question I have that isn't answered in this enormous thread is where do I go for professional help? Apparently I'm "obsessed" and need help. Well, that's what the wifey says:crazy:. Funny thing is she keeps asking what I'm cooking next
I will say it's been very satisfying cooking delicous food on something I've made. There has been a huge learning curve trying to get my heat dialed in and settled. Still figuring it out. The drum is tight, no leaks, I can have it stone cold from 350degrees in less than 45 min. I've got 2-3/4" ball valves and 1-3/4" capped nipple for intakes and I use the 2" bung for exhaust. I try to catch my temp on the way up. Shut down first intake at 180 and start adjusting second intake around 200. I block the intakes from wind and I keep my start up procedure the same. 12 lit briqs on top of my basket. I use kingsford original charcoal. I think the combo of a new drum, new to bbq, and being overly excited is my main problem. Besides, for me, building the drum and figuring it out is the fun part. The food is just a bonus!:-D |
You do need help- you never once mentioned a second barrel. Are you sure you are commited to this?
|
Technically my current barrel is my 2nd. The first i made to complicated and it is now a brush burner in the backyard. I've also built my own cold smoke generator(haven't smoked any food yet) and Im collecting materials to build an offset so I can try my hand at a wood fired smoker.
The way I see it my only real 'problem' is not having enough coin to get a BGE. :becky: |
Ahhh.... so you really are sick! LOL
|
guess i am. thank you?
|
Thank you for the tip.. pliers opened on the top on inside of the bung hole and twist allowed me to open.. and I have the 2" one plus I also have some 3/4" hole that I opened as well.
So what I do now is leave my 3 vents at the top on the side open most of the time. I open the bung hole only if I have to get the temp climbing faster. Then when it's there I plug it up again and leave one and a half of my intake vents at the bottom. This seems to work. However I see that my temp on the lid and temp on the side of barrel at cooking grate is still quite a bit lower than internal temp on the grate by the food. I will start looking for a pizza pan type of thing to place between the fire and food and drill some holes. I imagine this will make the temp more even around the cooking area. |
Quote:
|
Ok!! I read the WHOLE thread. Only took a couple weeks off and on. What an entertaining and informative read. I will be building my own UDS KISS style. I am SO tired of fighting with my moded ECB!! I get good results, mind you, but the "set it and forget it" idea of a UDS makes a lot of sense to me.
Thank you ALL for you input, questions, advice, comedy, wins and losses. With luck, I will have something to add to this thread and additional ones as as well. I also have another coworker or two interested in UDSs. I may build a few and sell/trade them. Talk to you all soon!! Thanks!! |
Quote:
But like you, I have another smoker (COS) Cheap Offset Smoker and keeping it up to temp is a big pain in the cold months. The UDS is amazingly easy to maintain temps and be very efficient in fuel usage! |
An ECB IS an El Cheapo Brinkman http://www.brinkmann.net/products/ou...tem=852-7006-0
I have made a couple modifications to it, including moving the legs to the outside, and drilling holes in the firepan. Check this out for other mods: http://www.randyq.addr.com/ecb/ecb.html This thing is killing me today with an 11 lb Butt on it. Q-view will follow.... Quote:
|
TTUDS Complete
Well I finally finished my UDS. I have a brisket going on it right now. Here's a photo of the finished drum and a link to the build thread.
http://i113.photobucket.com/albums/n...s/DSC_0112.jpg Texas Tech Drum Corps (UDS Build Thread) |
Wisconsin Brethren: 16 Gallon Drum?
Any Wisconsin Brethren know of a place where I might get a 16 gallon steel drum (27" x 14")? NOw that I have had success at home, I'm thinking of making a mini UDS for my campsite in Green Lake. No barrels of this size on craigslist.
Thanks! |
All times are GMT -5. The time now is 06:31 AM. |
|
Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.