If a Redneck wanted to build a UDS - Page 9

KaBudokan · 05-22-2009, 10:47 AM

Quote:

Originally Posted by Norcoredneck

Put one on outside, one on inside.

Right, but even so, even with the shortest nipples I could find at HD, I still have a good amount of space between the ring and the barrel, so if I'm not careful, I end up unscrewing the nipple with the cap. The locknuts won't tighten far enough on the nipple - like the nipple expans closer to the center...

Skidder · 05-22-2009, 11:04 AM

Use a bolt on floor plate instead.

KaBudokan · 05-22-2009, 11:23 AM

The floor plate looks like a good idea! What section would that be in - plumbing?

Skidder · 05-22-2009, 02:39 PM

Try electrical.

Norcoredneck · 05-22-2009, 05:39 PM

Quote:

Originally Posted by KaBudokan

Right, but even so, even with the shortest nipples I could find at HD, I still have a good amount of space between the ring and the barrel, so if I'm not careful, I end up unscrewing the nipple with the cap. The locknuts won't tighten far enough on the nipple - like the nipple expans closer to the center...

Ok here is the deal. The nipples are not threaded enough or a dull die was used. I meant put the locknuts on the same side. First one on as far as you can get it on, then through can, then 2nd lock nut. So from outside you have threads, center of nipple, threads, locknut, can, locknut. Guarantee it will work.
This is how I advised LT72884 how to do it.

420 Reasons to Eat · 05-22-2009, 07:03 PM

LeckembyBrosCustoms:

Thank you for the heads up on Harbor Frieght, this is going to save me a lot.

Where do all you So-Cal residents get your wood? California Charcoal?

HeSmellsLikeSmoke · 05-22-2009, 07:13 PM

Quote:

Originally Posted by 420 Reasons to Eat

LeckembyBrosCustoms:

Thank you for the heads up on Harbor Frieght, this is going to save me a lot.

Where do all you So-Cal residents get your wood? California Charcoal?

Hey 420, please go over the Cattle Call and introduce yourself so we can all give you a proper Brethren welcome.

KaBudokan · 05-22-2009, 09:54 PM

Thanks Norco - that makes sense now... I may try to rearrange this tomorrow.

Sorry - I'm a little slow sometimes... lol

LeckembyBrosCustoms · 05-23-2009, 09:07 PM

I am interested in the lid, I got a second drun and cut the end off. I then used a body hammer and flared out the cut end to fit atop my drum.... I was a bit worried about the webber grill lids because that look like they just sit atop the drum. I am going to have to put exhaust holes and a handle but it seems to fit pretty good . I still need to try it out ... Norco I am definately interested in a lid that has been a sticking point for me... thanks Dan

coreman23 · 05-30-2009, 12:43 PM

Hey guys, I just joined and am having a hell of a time finding a barrel for a UDS build.

Sorry for the hijack, but for those in So-cal, where are you finding unlined open barrels? I live in Big Bear and don't have anything around me. If you guys could point me in the right direction on where to find some barrels, I would really appreciate it!!!!

I really like this build and will probably copy it.

Norcoredneck · 05-30-2009, 12:53 PM

Quote:

Originally Posted by coreman23

Hey guys, I just joined and am having a hell of a time finding a barrel for a UDS build.

Sorry for the hijack, but for those in So-cal, where are you finding unlined open barrels? I live in Big Bear and don't have anything around me. If you guys could point me in the right direction on where to find some barrels, I would really appreciate it!!!!

I really like this build and will probably copy it.

There is a drum place just off the 60 at main, north of the freeway. I think it is called D&R , PM Garth57 he has been there.

Also here in Ontario
http://orangecounty.craigslist.org/for/1164978825.html

LeckembyBrosCustoms · 05-30-2009, 10:32 PM

I cut a second drum at first ring about 12 inches.

LeckembyBrosCustoms · 05-30-2009, 10:34 PM

Used a body hammer to flare out the end

LeckembyBrosCustoms · 05-30-2009, 10:35 PM

added exhaust pipes and a handle

LeckembyBrosCustoms · 05-30-2009, 10:39 PM

worked great Thanks Norco for all the work that you did I followed you plans and it worked just like you said.... i was amazed the temp was a constant 220 for 8 hours. I used maybe 2.5lbs of lump charcoal. My family fought for 2nds. And there were no leftovers. I am greatful for all of your hard work thanks Dan

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My next Build.........Opinions wanted	Igotgas	Q-talk	4	01-27-2012 11:50 PM
Completed 1st UDS build/First cook on new UDS	gambler	Q-talk	21	09-06-2011 09:41 PM
If I wanted to build a UDS...	JMSetzler	Q-talk	18	07-19-2011 06:41 AM
Wanted: Chicken Glaze (UDS)	Sammy_Shuford	Q-talk	12	01-01-2011 06:05 PM
Would it be a Redneck Guru for my UDS?	pahutchens	Q-talk	20	09-22-2010 09:23 AM

05-22-2009, 11:04 AM	#122
Skidder Babbling Farker Join Date: 02-02-08 Location: Westfield,Ma. Downloads: 0 Uploads: 0	Use a bolt on floor plate instead.

05-22-2009, 11:23 AM	#123
KaBudokan Is lookin for wood to cook with. Join Date: 05-13-09 Location: Bethlehem, PA Downloads: 0 Uploads: 0	The floor plate looks like a good idea! What section would that be in - plumbing?

05-22-2009, 02:39 PM	#124
Skidder Babbling Farker Join Date: 02-02-08 Location: Westfield,Ma. Downloads: 0 Uploads: 0	Try electrical.

05-22-2009, 07:03 PM	#126
420 Reasons to Eat Is lookin for wood to cook with. Join Date: 05-21-09 Location: North Hollywood, CA Downloads: 0 Uploads: 0	LeckembyBrosCustoms: Thank you for the heads up on Harbor Frieght, this is going to save me a lot. Where do all you So-Cal residents get your wood? California Charcoal?

05-22-2009, 09:54 PM	#128
KaBudokan Is lookin for wood to cook with. Join Date: 05-13-09 Location: Bethlehem, PA Downloads: 0 Uploads: 0	Thanks Norco - that makes sense now... I may try to rearrange this tomorrow. Sorry - I'm a little slow sometimes... lol

05-23-2009, 09:07 PM	#129
LeckembyBrosCustoms Found some matches. Join Date: 05-20-09 Location: Colton Ca Downloads: 0 Uploads: 0	I am interested in the lid, I got a second drun and cut the end off. I then used a body hammer and flared out the cut end to fit atop my drum.... I was a bit worried about the webber grill lids because that look like they just sit atop the drum. I am going to have to put exhaust holes and a handle but it seems to fit pretty good . I still need to try it out ... Norco I am definately interested in a lid that has been a sticking point for me... thanks Dan

05-30-2009, 12:43 PM	#130
coreman23 Found some matches. Join Date: 05-28-09 Location: Big Bear, CA Downloads: 0 Uploads: 0	Hey guys, I just joined and am having a hell of a time finding a barrel for a UDS build. Sorry for the hijack, but for those in So-cal, where are you finding unlined open barrels? I live in Big Bear and don't have anything around me. If you guys could point me in the right direction on where to find some barrels, I would really appreciate it!!!! I really like this build and will probably copy it.

05-30-2009, 10:32 PM	#132
LeckembyBrosCustoms Found some matches. Join Date: 05-20-09 Location: Colton Ca Downloads: 0 Uploads: 0	I cut a second drum at first ring about 12 inches.

05-30-2009, 10:34 PM	#133
LeckembyBrosCustoms Found some matches. Join Date: 05-20-09 Location: Colton Ca Downloads: 0 Uploads: 0	Used a body hammer to flare out the end

05-30-2009, 10:35 PM	#134
LeckembyBrosCustoms Found some matches. Join Date: 05-20-09 Location: Colton Ca Downloads: 0 Uploads: 0	added exhaust pipes and a handle

05-30-2009, 10:39 PM	#135
LeckembyBrosCustoms Found some matches. Join Date: 05-20-09 Location: Colton Ca Downloads: 0 Uploads: 0	worked great Thanks Norco for all the work that you did I followed you plans and it worked just like you said.... i was amazed the temp was a constant 220 for 8 hours. I used maybe 2.5lbs of lump charcoal. My family fought for 2nds. And there were no leftovers. I am greatful for all of your hard work thanks Dan