拉猪肉
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
 
Thread Tools
Old 05-03-2014, 04:55 PM   #1
Theboz1419
Take a breath!

 
Theboz1419's Avatar
 
Join Date: 08-13-09
Location: Elgin, IL
Default The Homebrewed Heatermeter in action

Hey, I thought I would post a my first run with my Heatermeter with the Servo attachment.

If you are not familiar with the HM, its a Raspberry Pi with an attached board that you make yourself for a lot cheaper then what you can buy premade. You can use Maverick probes or Thermowork probes. Cases are 3d printed and also the servo case. Byran has put a lot of work into designing the HM and now anybody can make one without much trouble.

Today, im going to try those dam Bacon Onion rings on some Hamburgers

here is a pic of the set up on my UDS


That's the servo in the 3d printed PLA attached to a fairly big blower lol


And a live feed from the Heatermeter

http://uds.servebeer.com

Today is learning day to adjust the settings to get a stable temp
__________________
Raspberry PI Heatermeter homemade temp controller, 2 UDS.
New Version 4.2 Heatermeter with K thermocouple support Available
PM me, if you would like a heatermeter pre-made, everything included, heatermeter, case, blower, SD card programmed, servo and case, no soldering needed ready for your network and BBQ.

Last edited by Theboz1419; 05-03-2014 at 05:55 PM..
Theboz1419 is offline   Reply With Quote


Old 05-04-2014, 03:48 AM   #2
Eggtastico
Full Fledged Farker
 
Join Date: 07-17-13
Location: Wales
Default

excellent :0D

I have recently finished my v4 build
going to try to build a v4.1 eventually.
Eggtastico is offline   Reply With Quote


Old 05-20-2014, 09:58 PM   #3
rftek
Got rid of the matchlight.
 
rftek's Avatar
 
Join Date: 07-19-10
Location: Austin, TX
Default

Looking good!

Is that the rotodamper servo?

I built a 4.0 a couple weeks ago and enjoy cooking with it.
__________________
1 UDS, 1 Weber 22" w/rotisserie
rftek is offline   Reply With Quote


Old 05-20-2014, 10:09 PM   #4
peeps
somebody shut me the fark up.

 
peeps's Avatar
 
Join Date: 08-09-13
Location: Denton, TX
Default

I got tired of waiting to see if someone would build me one and just bought a Guru

Nice work!
__________________
***** North Texas Brethren Bash - Spring 2015 - In Planning Now ***** (link)

- Earl - My Custom Vertical Offset Smoker by AJ's Custom Cookers (build link)
- Colt - Superior SS-2 w/ DigiQ DXII- Courtesy of Gainesville Jaycees and Superior Smokers
- Weber Kettle 22.5 OTG w/ Craycort Cast Iron Grates
- Major - Mini WSM (from SJS)

Certified IMBAS MOINK Baller! (Certificate of Authenticity) / Join the fun in the Throwdowns!
peeps is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 06:44 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.