ブタ
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 01-03-2014, 04:49 PM   #1
MoBettaQ
Is lookin for wood to cook with.
 
Join Date: 07-07-09
Location: SOCAL
Downloads: 0
Uploads: 0
Default Boneless Pork Shoulder Internal Temp

Friends, I deboned, butterflied, rubbed, rolled and smoked a 4lb pork shoulder roast "Porchetta Style" for New Years.

The problem: It was overdone.

The details:
  • Roast appeared to be a whole pork butt sliced in half
  • Rolled, I had what looked like a mini-ham. A ~10" conical section maybe 4" dia at one end and 6" at the other.
  • Weber 18" WSM
  • Kingsford Briquets
  • 4 Hickory chunks
  • Accurate digital thermometer in the thickest part of the pork and one in the smoker beside the pork at about half the thickness of the roast above the grate.
  • Water pan filled, drip pan on lower grate.
  • Pork was on the upper grate in the smoker and running @ ~225 @ 2am.
  • Checked ~6am and about every half hour thereafter to maintain 225.
  • Roast was naked the whole time, no foil.
  • Off at 6:30 after 16 1/2 hours at 186 degrees, wrapped in foil and rested 30 mins in a small cooler.
Discussion: I've smoked whole, bone-in butts to 196 or so with great success. Succulent, pulled nicely. My experience cooking them is they get to 170ish, stall for a while and then move on up to the 180s and 190s at a fairly constant pace. This roast seemed to stall twice - 170 and then again around 180. I gave up and finally pulled it at 186 as we were getting to dinner time. We found the meat a bit mushy and dry as compared to a pulled whole butt.



What I'd like is to understand how to get this smaller, boned roast to perfect slicing or pulling doneness. the "190s for slicing and 200 or so for pulling" rule of thumb didn't work so much for me this time. I've searched this forum and others without much success.

Thanks.
__________________
2013 18.5" WSM, 2002 22.5" Weber OTP, 200X Weber Genesis Silver C, Taylor 9306
MoBettaQ is offline   Reply With Quote


Unread 01-03-2014, 06:01 PM   #2
IamMadMan
Babbling Farker
 
IamMadMan's Avatar
 
Join Date: 07-30-11
Location: Southern New Jersey
Downloads: 0
Uploads: 0
Default

If are trying to cook it as a roast for slicing, I would have pulled it at about a 165-170 Internal temperature and let it rest for 20 minutes...
__________________
Humphrey's DownEast Beast W/BBQ Guru
IamMadMan is offline   Reply With Quote


Unread 01-03-2014, 06:09 PM   #3
Offthehook
is One Chatty Farker

 
Offthehook's Avatar
 
Join Date: 12-04-12
Location: Los Angeles, CA
Downloads: 0
Uploads: 0
Default

I looked at your whole process. I could be wrong but it was overdone for 2 reasons. 16 1/2 hours is way too long for that cut. I would bump up the temp and get it done sooner. Second madman mentioned it, were you going for a "roast" or more like a pulled pork. If so you still cooked too long for roast and not high enough internal temp for the pulled style you have had success in the past with.
__________________
Taylor-WSM 18.5 with Wifi Stoker, Kamado Smoker BBQ, and lots of charcoal. 180 club-Chicken
Offthehook is offline   Reply With Quote


Unread 01-03-2014, 07:04 PM   #4
BBQ Bandit
Babbling Farker

 
BBQ Bandit's Avatar
 
Join Date: 02-15-08
Location: Harrisburg, PA
Downloads: 1
Uploads: 0
Default

Agree - if intended for slicing...
160 max for pork butt/shoulder.
140 max for porkloin/boneless roast
__________________
Lang 84 Deluxe Kitchen known as "The Glamazon" , Custom Klose Backyard Chef... of Snot, and a 22.5 WSM

Former smokers;
Lang 60 Mobile - The Damsel II, Lang 48 Patio - The Damsel, Bubba Keg Grill - RIP, Double Barrel Smoker and a BSKD
BBQ Bandit is online now   Reply With Quote


Unread 01-04-2014, 12:10 PM   #5
MoBettaQ
Is lookin for wood to cook with.
 
Join Date: 07-07-09
Location: SOCAL
Downloads: 0
Uploads: 0
Default

Thanks to all of you. That makes sense.

I will go for a slicing temp for this roast next time by running maybe 275 and pulling at 160-170 as you've recommended.
__________________
2013 18.5" WSM, 2002 22.5" Weber OTP, 200X Weber Genesis Silver C, Taylor 9306
MoBettaQ is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 12:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts