ブタ
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 02-05-2013, 08:44 AM   #1
HOPTOAD
Knows what a fatty is.
 
Join Date: 09-17-10
Location: Palmyra, Va
Downloads: 0
Uploads: 0
Default Weber Performer Restore- Help

Brethren,

Just scored (I use that term loosley) a weber performer date code DI in dark green. When I got it home and started cheking it out I noticed the igniter was not working and the flame was more orange than blue. Took it apart this morning and got the igniter working but the flame is still the same.. more orange than blue. I would like to clean the end of the gas line that connects to the grill but wanted some advice as to what others have done to clean it out? I was thinking of soaking the end of the gas line in vinegar.

The second issue, there is a hole in the bottom of the bowl, right where one of the legs would attach to the bottom. The hole is about the size of a dime and the rust is isolated to one area. I somewhat fixed it buy putting a stainless bolt w washer on each side and a lock nut to cover the hole. Worked ok but after I got the ignition system working I noticed that the washer was not covering the entire hole. Had some plyers laying nearby so I tried to move the washer by force instead of loosing it and repositioning it (lazy mod). Well wouldn't you know it I knocked another small hole in it abouth the size of the end of a bic pen. Probably just end up putting another smaller stainess screw through that one as well but wanted to see if any other options were available. I do not have a welder but had considered JB Weld.

Any other repair tips for a rusted out kettle bowl?

Thanks for your help,

HOPTOAD
HOPTOAD is offline   Reply With Quote


Unread 02-05-2013, 09:03 AM   #2
PaPaQ
is One Chatty Farker

 
PaPaQ's Avatar
 
Join Date: 02-07-07
Location: Midland, NC
Downloads: 0
Uploads: 0
Default

The more orange than blue problem is caused by lack of air, It needs more air. I can't remember if the Performer had air adjustment or not, maybe somebody else will know.
PaPaQ is offline   Reply With Quote


Unread 02-05-2013, 09:59 AM   #3
MisterChrister
is One Chatty Farker
 
Join Date: 04-28-12
Location: Richland Center, WI
Downloads: 0
Uploads: 0
Default

There's a ton of great info in this thread by Q-Dat. Good luck! http://www.bbq-brethren.com/forum/sh...d.php?t=108452
__________________
Kettleheads Anonymous Platinum Member
MisterChrister is online now   Reply With Quote


Unread 02-05-2013, 10:04 AM   #4
charrederhead
is One Chatty Farker
 
Join Date: 06-29-12
Location: Thomaston, CT
Downloads: 0
Uploads: 0
Default

When I bought a used SS Performer last year it had a small, yellow flame.

Got a piece of wire and snaked it in there and out came a dime-sized spider!

Good blue flame ever since.
__________________
cimarron o/s, blk&grn ssp, blu mt, red & brn daisies, sjp, wsm, ga, 26.75, 2010 plt
charrederhead is online now   Reply With Quote


Unread 02-05-2013, 11:00 AM   #5
NRA4Life
is One Chatty Farker

 
NRA4Life's Avatar
 
Join Date: 07-07-09
Location: Newark, OH
Downloads: 0
Uploads: 0
Default

I took the igniter off the stainless tube, and took the tube off the rubber line then took it inside and washed it out in the sink. It mostly had dirt or wasp mud or something in there, but when I got it cleaned and put back together, it has worked like a champ.
__________________
- Kevin
Team: Smitty's Real Pit BBQ
KCBS CBJ
Superior SS-3 - Courtesy of Gainesville Jaycees and Superior Smokers
2 Custom Built Reverse Flow Stickburners
Weber 22.5" WSM
Weber 26.75" OTG
Weber Blue 2000 Stainless Performer
Weber Red 1998 Stainless Performer
NRA4Life is offline   Reply With Quote


Unread 02-05-2013, 12:11 PM   #6
J'ville Grill
is Blowin Smoke!

 
Join Date: 11-18-10
Location: USA
Downloads: 0
Uploads: 0
Default

Maybe you could replace the bowl with another one. If it's rusted out there's really no good fix for it.
__________________
Rick
J'ville Grill is offline   Reply With Quote


Unread 02-05-2013, 11:04 PM   #7
caliking
is One Chatty Farker

 
caliking's Avatar
 
Join Date: 01-13-10
Location: Houston, TX
Downloads: 0
Uploads: 0
Default

Quote:
Originally Posted by J'ville Grill View Post
Maybe you could replace the bowl with another one. If it's rusted out there's really no good fix for it.

I think I looked into this when I restored my redhead ss performer. The bowl was going to be $90 or so, but it wouldn't be red since it was discontinued. If I ever find a redhead performer with a decent bowl, I may replace it.
__________________
EZ wood handled 3 wheeler | OTS | OTS mod to OTG | Ladybug SS Performer | UglyDrumTandoor | UDS v1 | midi UDS with red nipples | SJG smoker mod | Simpsons SJS | Simpsons OTG | WGA charcoal | SJP | Stacked brick WFO | Lodge Logic Sportsman's Grill cast iron hibachi/sigri | LBGE | sbge | mini bge
caliking is offline   Reply With Quote


Unread 02-05-2013, 11:23 PM   #8
kds9547
is one Smokin' Farker

 
kds9547's Avatar
 
Join Date: 09-18-12
Location: Lugoff, SC
Downloads: 0
Uploads: 0
Default

I got so frustrated with that propane starter I don't even use it anymore. Seemed I was cleaning it every third cook or so. I use a chimney and the paraffin wax cubes. They are dirt cheap and work like a champ for me.
kds9547 is offline   Reply With Quote


Unread 02-06-2013, 09:36 AM   #9
HOPTOAD
Knows what a fatty is.
 
Join Date: 09-17-10
Location: Palmyra, Va
Downloads: 0
Uploads: 0
Default

Thanks everyone for the replies. I spent about 3 hours last night giving the grill a interior deep clean w oven cleaner, a razor scraper and some brillo.. still have about 1 to 1 1/2 hours to go. Could have gotten it done last night but I broke the scraper. Getting that replaced today then going to try to finish it up tonight. I have never seen so much gunk built up on a grill I am talking a good quarter inch on the rim and a eigth of an inch on the top of the bowl. Fired her up this morning just to make sure the ignitor was still working.. started on the third click w a blue flame..nice. I think tonight before I start cleaning I will get the grill good and warm then start again w the oven cleaner/ razor scraper. One thing I didnt think of til this morning is that I have a weed burner, that would have made quick work of the project if I had some propane...no such luck. Thinking I might have to get that filled when I pick up the scraper. One other good thing. The hole I knocked in the bottom is a little tiny thing maybe the size of the tip of a bic pin.. Think I will leave that be.
HOPTOAD is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 10:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts