喫煙者
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 11-17-2012, 03:35 PM   #1
kpd12
Got rid of the matchlight.
 
Join Date: 08-29-07
Location: Texas
Downloads: 0
Uploads: 0
Default Mini UDS Temp Control Problems

I have lurked on this site for years, only posting a couple times in the past. I recently decided, however to make an attempt at building a Mini UDS and did so using a 16 gal drum, and the lid and grates from a Weber Smokey Joe. I placed four intakes at approximately 2 inches from the bottom, evenly spaced and inserted ¾“ x 2 inch threaded nipples in three of the intake holes and a ¾” ball valve in the fourth. I made a basket using ¾” expanded metal wrapped around the charcoal grate from the Smokey Joe. The charcoal grate sits approximately an inch above the intakes and the basket itself is approximately 11 inches in diameter and 9 inches tall. Using the minion method I have tried filling the basket approximately ½ to ¾ full, once with lump charcoal and hickory chunks and another time with Kingsford Briquettes and hickory chunks. I usually then light about a dozen briquettes and place them on top of the basket. Once lit, with all caps off the intakes and the ball valve wide open I can easily get up to temp, yet after capping the three nipples and no matter where I seem to adjust the ball valve and the exhaust on the Smokey Joe Lid, I just cannot seem to keep the temp below 300 degrees. Anyone have any ideas as to what I am doing wrong? I do have some smoke leaking from the lid and have even tried wrapping foil around the top of the barrel to cut down on the air leak. Unfortunately I am unable to search the site although I did read multiple posts related to UDS' and Mini UDS' to the point that my head hurts… Thanks in advance.... Mike
kpd12 is offline   Reply With Quote


Unread 11-17-2012, 09:56 PM   #2
Pugi
Full Fledged Farker
 
Pugi's Avatar
 
Join Date: 09-21-11
Location: Idaho
Downloads: 0
Uploads: 0
Default

Mike, after you verify you don't have a air leak, I would start with less briquettes. I use 12 for a 55 gallon drum. Just a guess would be starting with 6. Cap off extra Intakes early and only have valve open at 200*. Then see where she settles. Pugi
Pugi is offline   Reply With Quote


Unread 11-17-2012, 10:05 PM   #3
fr8erfxr
Knows what a fatty is.

 
fr8erfxr's Avatar
 
Join Date: 12-29-10
Location: Lake Cormorant, MS
Downloads: 0
Uploads: 0
Default

I start mine with 6 or 7 briquettes and catch it on the way up. I have also found that I have to close off my exhaust to about 2/3 open helps.
__________________
UDS w/Pitmaster iQUE 110, mUDS, Weber Performer, Grillmaster gasser, Red Thermapen, Modded Maverick ET-73 & ET 732.
fr8erfxr is offline   Reply With Quote


Unread 11-18-2012, 06:48 AM   #4
kpd12
Got rid of the matchlight.
 
Join Date: 08-29-07
Location: Texas
Downloads: 0
Uploads: 0
Default

Thanks for the responses. I will try your recommendations and see what happens.
kpd12 is offline   Reply With Quote


Unread 11-18-2012, 07:39 AM   #5
Rich Parker
Babbling Farker

 
Rich Parker's Avatar
 
Join Date: 06-20-09
Location: Grand Rapids, MI
Downloads: 0
Uploads: 0
Default

A little bit of smoke coming around the lid isn't your problem. I always have smoke there with no problems. Sounds like an air leak around your intakes because even with starting with too much lit charcoal you should be able to catch it on the way up and stabilize it.
__________________
WSM and UDS - iBQ'n BBQ Team co-founder TheBBQSuperstore.com sponsored by Deep South Smokers
Rich Parker is offline   Reply With Quote


Unread 11-18-2012, 09:07 AM   #6
Bludawg
somebody shut me the fark up.
 
Bludawg's Avatar
 
Join Date: 07-04-09
Location: Jonesboro,Tx
Downloads: 0
Uploads: 0
Default

You have an air leak seal the connection where the nipples penetrate the drum with some RTV.
__________________
I never met a Cow that I didn't like with a little Salt & Pepper! Certified PORK-A-HOLIC
Bludawg is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 06:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.