喫煙者
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 12-23-2011, 04:28 AM   #1
fedex
Full Fledged Farker
 
fedex's Avatar
 
Join Date: 06-21-10
Location: Cypress, CA
Downloads: 0
Uploads: 0
Default WSM 18 1/2 Grommet Mod

I know this has been discussed here but I can't find it. I would like to know if the 3/8 Grommet set sold by Cajun Bandit will work on 18 1/2 WSM? Where is it installed? I'll be getting the Maverick ET-732 (hopefully today) as a gift to myself for xmas. Thanks in advance for any help or advice.
__________________
UDS, Jumbo Joe 2013, 26" Weber, SS Blue Performer, WGA Charcoal, Q100 & Wife Model#1962
fedex is offline   Reply With Quote


Unread 12-23-2011, 06:32 AM   #2
accuseal
On the road to being a farker

 
accuseal's Avatar
 
Join Date: 08-17-11
Location: Strongsville, Ohio
Downloads: 0
Uploads: 0
Default

They will work no problem. Install just underneath the level of your top rack about 2" apart. Put some duct tape on the wsm before drilling or you'll chip the powder coating.

Sent from my SCH-I905 using Tapatalk
__________________
RUB-A-RIB-RIB BBQ
Two Modified WSM 22, iQue 110, CyberQ, Traeger Texas, Smokey Joe, Weber Gasser
CBJ
accuseal is offline   Reply With Quote


Unread 12-24-2011, 10:03 PM   #3
Riskyguy
On the road to being a farker
 
Join Date: 07-16-11
Location: Fort Collins, CO
Downloads: 0
Uploads: 0
Default

The standard threaded lamp rod will do the same thing for about $5. Go to the Virtualweberbullet site for modification info. Simple to do and works well.
Riskyguy is offline   Reply With Quote


Unread 12-24-2011, 10:18 PM   #4
alane
Knows what a fatty is.
 
Join Date: 04-17-11
Location: Minnesota
Downloads: 0
Uploads: 0
Default

I didn't want to drill my WSM to get my ET-732 to fit so I ended up using a roll pin and a set collar. The probe still can't fit through the pin, but the braided wire does. It takes a little bit more for the final assembly but again I didn't want to drill. Pictures are attached.

IMG_0905 (Small).JPG

IMG_0912 (Small).JPG
alane is offline   Reply With Quote


Unread 12-25-2011, 05:33 AM   #5
morgaj1
is one Smokin' Farker

 
Join Date: 09-06-11
Location: Alabama
Downloads: 0
Uploads: 0
Default

The 3/8" grommet from Cajun Bandit is what I have on my UDS and the Maverick probes fit just fine.
__________________
Eric

A nation of sheep will soon have a government of wolves - Edward R. Murrow
morgaj1 is offline   Reply With Quote


Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Concerns over using a 25 CFM fan w/ a 22" WSM & Question on Grommet hole ?? MilitantSquatter Q-talk 17 11-09-2011 06:49 AM
Questions: WSM Grommet Hole NS Mike D Q-talk 2 11-01-2011 09:49 AM
WSM Handle Mod mwmac Q-talk 16 02-18-2011 04:11 PM
WSM Mod on UDS Cliff H. Q-talk 4 01-30-2008 09:22 PM
WSM Rain Mod tommykendall Q-talk 24 10-16-2007 11:13 AM

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 08:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.