ブタ
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 03-22-2005, 02:38 AM   #1
BrooklynQ
Banned
 
BrooklynQ's Avatar
 
Join Date: 07-18-04
Downloads: 0
Uploads: 0
Default How to make your own charcoal

To make 30-40 lb. of charcoal, you will need:

* A clean 55 gallon metal drum with the lid cut off roughly (you will be able to reuse this drum many, many times).
* Enough seasoned wood to fill said drum, chopped into big fist-size pieces--about 5"x5", and the wood just needs to be a couple months seasoned, although the dryer the wood, the faster the process.
* A bag of sand.
* 3 or 4 bricks.
* A case of beer (optional).

Start by punching or cutting 5 holes in the bottom of the drum which are each 2" square. Try to keep them towards the center. Put the drum down on the bricks, placed so it is up off the ground and fill it with the wood.

Start a fire in the drum. When it is going well, put the top back on to reflect back the heat. Since it was cut off roughly, there will be slight gaps to allow a draft.

Now, turn the whole thing over, placing it back onto the bricks. (This is where you might need the case of beer to convince several men to help you lift the sucker. It will be heavy. And mind the lid doesn't fall off!) Wait, consuming the beer as necessary.

The smoke will start out white. This is the water vapor burning off. Next the smoke will go blue/gray which is the alcohols and phenols burning off.

Then the smoke appears yellow, which is the tar burning off. Finally the smoke will clear and you will just see waves of heat. When this happens, carefully remove the bricks from underneath the drum. Take some sand and make a pile around the bottom of the drum, plugging up the bottom draft. Also, cover the top with either a piece of turf or a large piece of metal. Use sand to seal around the turf/metal so no air can get into the drum. We are trying for a closed system here. If air/oxygen/fire-fuel DOES get into the drum, the charcoal will just burn up. Not what we want. Also, try not to let the sand fall down into the drum through the holes.

Allow the drum to sit and cool (2-3 hours). Then turn back over, pry off the top and remove your charcoal. If there is a spark, the charcoal may "catch", but just douse it with some water. The charcoal will still be hot enough to dry out. Repeat above process as necessary.

By the way. I know this should be obvious, but, only use hardwood for your charcoal. By hardwood, I mean any broadleaf tree. Such as maple, almond, ash, alder, hickory, cherry, etc. You can use non-broadleaf wood (such as pines, firs and conifers) for charcoal but that charcoal will never get hot enough when it is burned. Therefore, it is only good for distillation purposes. Which, in itself, might be a handy tip. Also, this creates one heck of a lot of smoke, so don't make charcoal when the neighbor's laundry is outside on the line. (Of course, by now, you all would know that but, just in case there are a few who haven't really done a lot of smoking yet... a word to the wise and all that!)

Thanks to my brother-in-law, Don Whiting, who taught me how to do this.

Here is another method for making lump charcoal--

John H Cartlidge--

I've recently been given a book on woodland crafts (1) which contains a very similar method - minus the juggling! As I've not had a chance to try it yet, I've reproduced the method verbatim. There are also a couple of small line drawings in the book illustrating the process.

1 Using a cold chisel prepare the drum by making five 2-inch holes in one end and completely removing the other end. Knock-up the cut edge of the open end to form a ledge(2).

2. Position the drum, open end upwards, on three bricks to allow an air flow to the holes in the base.

3 Place paper, kindling and brown ends (incompletely charred butts from the last burn) into the bottom of the drum and light.

4 Once it is burning well, load branchwood at random to allow air spaces until the drum is completely full. Keep the pieces to a fairly even diameter but put any larger ones to the bottom where they will be subjected to a longer burning.

5 When the fire is hot and will clearly not go out, restrict the air access around the base by using earth placed against it, but leaving one 100mm (4in) gap. Also place the lid on top, leaving a small gap at one side for smoke to exit

6 Dense white smoke will issue during the charring process. When this visibly slows, bang the drum to settle the wood down, creating more white smoke.

7 When the smoke turns from white (mainly water being driven off) to thin blue (charcoal starting to burn) stop the burn by first closing off all air access to the base using more earth, and second by placing the lid firmly on its ledge, and making it airtight by the addition of sods and soil as required. The burn will take between three and four hours.

8 After cooling for about 24 hours, the drum can be tipped over and the charcoal emptied out onto a sheet for grading and packing.
BrooklynQ is offline   Reply With Quote


Unread 03-22-2005, 07:41 AM   #2
BigBelly
is one Smokin' Farker
 
Join Date: 07-28-04
Location: Elizabeth CO
Downloads: 0
Uploads: 0
Default

I read an article very similiar to this about 6 months ago. Once I find some time I will try my hand at making some of my own lump. It sure won't hurt to save a few bucks on buying lump or charcoal.

Thanks for the read, BrooklynQ.
__________________
Big Boy Jerky
Authentic Hardwood Smoked Jerky
[url]www.bigboyjerky.com[/url]

Family BBQ and Catering
~: Proud Bandera Owner :~
BigBelly is offline   Reply With Quote


Unread 03-22-2005, 09:56 AM   #3
kellyman
Is lookin for wood to cook with.
 
Join Date: 06-15-04
Location: dallas, tx
Downloads: 0
Uploads: 0
Default

man you are hard core.... that all sounds a bit ill fated to me. more power to ya, but I think I'll just go down to the store and buy a bag.

happy Q'ing!
kellyman is offline   Reply With Quote


Unread 03-22-2005, 07:59 PM   #4
The_Kapn
Moderator Emeritus

 
The_Kapn's Avatar
 
Join Date: 04-08-04
Location: Marianna, FL
Downloads: 0
Uploads: 0
Default

Rob,
Quote:
To make 30-40 lb. of charcoal, you will need:
Plus:
Quote:
A case of beer (optional).
My math may be off, but this sounds like "a wash" with just going to Wally World and picking up a "48'er" of Kingsford.
Could be wrong.
Think I wil use the beer to help along the que
Interesting article though.

TIM
__________________
"Flirtin' with Disaster" BBQ Team (RETIRED)
FBA and KCBS Cook and Judge.
Former owner of a WSM, a Smokey Joe, a Charbroil Commercial gasser (junk), the legendary "StudeDera", a Fast Eddy PG500, and Sherman.
Now cooking with a Yoder YS640
Proud Pellet guy cooking on real wood.
The_Kapn is offline   Reply With Quote


Unread 03-22-2005, 10:06 PM   #5
BrooklynQ
Banned
 
BrooklynQ's Avatar
 
Join Date: 07-18-04
Downloads: 0
Uploads: 0
Default

Quote:
Originally Posted by kellyman
man you are hard core.... that all sounds a bit ill fated to me. more power to ya, but I think I'll just go down to the store and buy a bag.
I've never done it, but thought the article was interesting
BrooklynQ is offline   Reply With Quote


Unread 03-23-2005, 08:45 PM   #6
evilpsych
Full Fledged Farker
 
evilpsych's Avatar
 
Join Date: 11-14-03
Location: KENTUCKY
Downloads: 0
Uploads: 0
Default

maybe if i had a buttload of unseasoned wood i wanted to use quick... i might use that method. but dang. how is that better than using seasoned splits? or a quick bag of lump or briquette to get the fire goin?
evilpsych is offline   Reply With Quote


Unread 03-23-2005, 09:16 PM   #7
racer_81
Babbling Farker
 
racer_81's Avatar
 
Join Date: 08-11-03
Location: Richmond, TX
Downloads: 0
Uploads: 0
Default

The method is tedious. But, you will know for certain what sort of wood your charcoal actually came from.
__________________
This Space Left Intentionally Blank
racer_81 is offline   Reply With Quote


Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
make charcoal by your self woodpelletsmoker Gravity Fed smokers and Grills 2 07-08-2011 10:13 AM
Make your own lump charcoal? TedW Q-talk 16 04-08-2011 11:54 AM
How to make Charcoal bingo1912 Q-talk 22 04-12-2010 12:50 AM
How to make LUMP charcoal Kickback BBQ on Guam Q-talk 24 09-28-2009 09:45 PM
Make lump charcoal Piedmont Q-talk 5 04-25-2006 03:46 PM

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 12:19 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts