|
Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking. |
|
Thread Tools |
02-07-2012, 12:11 AM | #9211 |
Full Fledged Farker
Join Date: 12-28-10
Location: Valencia, CA
|
Used my UDS (built in early Jan 2012) for the first time on a long cook. Been doing mostly moink balls and ABT's on it, but did a pork butt for Superbowl. Not only did it cook a little faster than my old offset, but it held 235-240 perfectly even for close to 10 hours. I finished an almost 8 lb pork butt in about 9.5 hrs. I opened it a couple times to spray with apple juice, and it dropped to about 215. Within 30 seconds of removing the caps off of the other three intakes, it started going back up quickly. Capped them back off and it just kept on cruising at 240
MAN I LOVE MY UDS!!!
__________________
Green OTG; Black OTS; UDS; mini-WSM; Weber Genesis Silver; USMC 86-94 |
|
02-12-2012, 01:12 PM | #9212 | |
Knows what a fatty is.
Join Date: 03-26-11
Location: Southlake, TX
|
Quote:
If you think about it, before you take that lid off, you only have a very small amount of combustion air coming in through your intakes. When you take that lid off, the fire gets a huge gulp of combustion air (by comparison). It will burn through that air hotter than if you had not taken the lid off. Your temp gauge drops only because there's some cool air in there at the moment, but the fire isn't running at that new cooler level, it's still hot as it was and even hotter now due to the extra air. It will easily catch up on its own. In fact, I think most drums will actually run up in temp after taking the lid off. Many turn their intake air off before taking the lid off to prevent too much air from getting in and causing a temp spike. |
|
|
Thanks from:---> |
02-12-2012, 03:18 PM | #9213 | |
Full Fledged Farker
Join Date: 12-15-09
Location: Antelope, CA (Sacramento metro area)
|
Quote:
One thing I've found is that if you cut the pork butt into ~3" slices and cook them like big steaks, the pork still comes out just as tender, but it takes MUCH less time to cook! Gotta go a bit easier on the rub though, because the surface area is so huge. Good thing to know when you only have ~5 hours to prep and cook some pork, and you'd otherwise decide against it. Possibly less moist pork is better than no pork at all... that's what I say. I'm using Chris Lilly's recipe, by the way. Best I've tried by a long shot, and those who try it enjoy it nearly to the point of what I'd call arousal... -Rodney
__________________
Char-Broil Commercial Series Gasser, ECB, MECO 4400 charcoal grill, 22.5" OTS, UDS built 3/20/2010 ([URL="http://www.bbq-brethren.com/forum/album.php?albumid=291"]Pics[/URL], [url="http://www.youtube.com/watch?v=bCyKypslPhs"]Video[/url]) Maverick ET-7 and ET-73, home-built 18A sous vide temperature controller IMBAS Certified MOINK Baller My blog: [url="http://think-create-eat.blogspot.com"] THINK + CREATE + EAT[/url] - [URL="http://www.facebook.com/pages/THINK-CREATE-EAT/115706441783448"]"Like" on Facebook[/URL] [B][COLOR=red]"Meat: It's what's for dinner. And lunch, breakfast, dessert..."[/COLOR][/B] |
|
|
02-12-2012, 05:36 PM | #9214 |
Babbling Farker
Join Date: 12-26-04
Location: Selma, TX(You better slow down when you hit town)
|
I started another thread but I wanted to memorialize the demise of UDS#1 on the thread where it all started. It finally succumbed to rust and had to be replaced.
__________________
Wannabe BBQ Illuminati |
|
Thanks from:---> |
02-12-2012, 07:25 PM | #9215 |
Babbling Farker
Join Date: 02-03-12
Location: Chickamauga, Ga
|
I hoping that this week I will have time to start mine. Cant wait to get it built and smoking.
|
|
02-13-2012, 10:37 PM | #9216 |
Found some matches.
Join Date: 02-13-12
Location: Corona, CA
|
mild rust inhibitor??
I've been looking at the grainger barrels labeled as "unlined" though coated with a "mild rust inhibitor". I live in an area where I wouldn't be able to burn out the barrel for hours.
Since this is a new barrel do I need to do a big burn out? Can I have the barrel sandblasted or get the coating off with a mild fire like with a 20lb bag of charcoal? I'm thinking of getting the 96 gallon drum because its 16 gauge (vs 18 on the 85). Thanks, M |
|
02-14-2012, 07:44 AM | #9217 | |
Knows what a fatty is.
Join Date: 11-26-10
Location: Somewhere, CT
|
Quote:
|
|
|
02-14-2012, 08:15 AM | #9218 | |
Found some matches.
Join Date: 01-09-12
Location: Winnipeg, CANADA
|
Quote:
...so what is so special about Chris Lilly's recipe? Do you mind to share it?
__________________
...it doesn't count if you burn it... |
|
|
02-14-2012, 03:15 PM | #9219 | |
Got Wood.
Join Date: 04-07-11
Location: Bowling Green, KY
|
Quote:
|
|
|
02-14-2012, 04:20 PM | #9220 | |
Found some matches.
Join Date: 02-13-12
Location: Corona, CA
|
Quote:
The grainger drum is brand spanking new direct from the factory. They have two options, one lined with the redish epoxy stuff and an unlined that has a 'mild rust inhibitor' coating. What I've read is that this mri is a lite oil of sum sort to prevent the inside of the barrel from rusting during shipment. I'm trying to verify what that oil is and can it be removed safely without doing a 4 hour burn. I'd love to leave the paint on the outside of the barrel intact to save an extra step The other question I have is can I achieve this hard burn using charcoal instead of wood to keep the smoke down/fire low - I don't want to scare the wife or the neighbors. Thanks much and best regards, Michal |
|
|
02-15-2012, 08:36 AM | #9221 |
Knows what a fatty is.
Join Date: 11-26-10
Location: Somewhere, CT
|
If it's just an oil, then scrub pad and good grease cutting dish soap should do the trick. And then the rest as I suggested; drying it, rubbing it all down with a thick coat of olive oil and burn it in. That burning is at least 350 which you can easily get with charcoal and your paint will have no issues. I can take mine to 450 without worrying about the outside paint.
|
|
02-15-2012, 04:00 PM | #9222 | |
Found some matches.
Join Date: 02-13-12
Location: Corona, CA
|
Quote:
I think I'm just going to order the barrel, wash a part of the inside and see if it rusts the next day or two, then I'll do the full wash and as you suggested do an burn with a bag of charcoal and food grade oil to give it a nice protective coating. I've been going through the pages here one by one and looking at the pictures. A lot of you guys have some stellar ideas that I plan on implementing, mainly: 1) Ball valves 2) Vent piping so you don't have to bend down to adjust intake temps 3) A hook on the lide to be able to hook it on the side while you're moving meat (so you don't have to put it on the ground or a table 4) hooks/shelving for accessories 5) wheels - castors maybe? I've seen a guy attach a dolly to his 6) ash basket with a pan underneath to make cleanup a snap 7) side handles to be able to move the unit around for storage/cleaning a few other things I have in my notes somewhere. |
|
|
02-15-2012, 05:45 PM | #9223 |
is Blowin Smoke!
Join Date: 05-09-11
Location: Granite City, Illinois (Near St. Louis "GO CARDS")
|
What about the top? Flat top or weber lid?
__________________
22.5 WSM, 120 Gallon Offset, Weber Performer, IQ-110, ET-732 |
|
02-15-2012, 09:12 PM | #9224 |
Found some matches.
Join Date: 02-13-12
Location: Corona, CA
|
Gonna go with a flat top...
|
|
02-17-2012, 11:32 AM | #9225 |
Full Fledged Farker
Join Date: 09-02-11
Location: Evans, GA
|
I'm having a difficult time trying to find a drum here in Augusta, GA. There is a guy in SC about 1.5 hours away that has a bunch of food grade drums for sale. There is also a oil company downtown that sell re-conditioned drums, that they say have been commercially cleaned and then this company buys for resale. So there is nothing in them. What should I do? Make the drive or stay local? TIA
|
|
Tags |
divided circle template, uds, ugly drum, ugly drum grill, ugly drum smoker |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ugly Drum Smoker | ironslob | Q-talk | 2 | 09-19-2010 10:16 AM |
Ugly Drum Smoker - Need Help | Bartkowiakj | Q-talk | 10 | 06-18-2010 09:38 PM |
One Ugly Drum Smoker | Steve_B | Q-talk | 15 | 09-21-2009 10:32 PM |
My (not-so) Ugly Drum Smoker. | hav | Q-talk | 47 | 11-05-2008 02:30 PM |
Ceramic Cooker Meets Ugly Drum Smoker - BUDCS - Concept Drum Discussion | Hook_Line_and_Sinker | Q-talk | 9 | 04-26-2008 02:24 PM |
|
|