Modified UDS question

Spyders03 · Apr 27, 2014

I have 2 barrels at my disposal, possibly 3. I was looking at doing a few mods.

1. Taking 1/3 or 2/3 of the second barrel and cutting and welding it on top of the base barrel, both standing upright. Thought this might get up further from the heat and provide extra room for a good sized second rack.

2. Thought about putting a baffle above the fire, could double as a water retainer holder, have seen this done, but undue of the results.

3. Welding feet on the bottom, 2 with wheels, for easier moving

4. Adding doors on the sides, at least one in the bottom to get to fire basket

Any thoughts on these would be greatly appreciated, I'm definitely not an expert and if you guys think any of these are bad idea, PLEASE let me know! You won't hurt my feelings, rather do it right the first time. Also, if there are any other tricks you guys have found that work great, please feel free to share!

Dadeo719 · Apr 27, 2014

YES! YES!! YES!!! YES!!!! I will now take my seat and finish my beer while you get to work!

mchar69 · Apr 27, 2014

If you do this, get a 3rd rack in there -esp. if you have a dome lid.

You also need to be able to reach in .
Ash control.
The joy of barrel smoking is absolute control of air inflow.
You need this as well.
As well as - it looks cool.

ebijack · Apr 28, 2014

1. why not use the 1/3 as the bottom/basket area. Would require lifting of the drum to get to the coal basket PIA... IMHO How much do you need to cook? Build 2 UDS's instead.
2. deflector for when required/wanted made from cheap pizza pan
3. Sure, but if you add a 1/3 barrel on top you will need a step ladder to reach inside. PIA IMHO
4. Door? Try a basic UDS first and see if you really want one. The coal basket lifts out real easy and can smoke for 20hrs when properly done on one load of coals.

delarob · Apr 28, 2014

Yeah, I was thinking a door on mine once but the potential for loss of heat/smoke is greater. The beauty of the UDS is its efficiency. No need to mess with what works.

SmokerKing · Apr 28, 2014

4. great idea! All mine have doors, fire basket access at any time, don't have to tear apart a drum and move racks around to get to the fire if needed. No air leaking. Add chunks or chips anytime, ramp up heat instantly by cracking door.

Side door works great if you take your time in fabricating!

Really, a smoker without easy access to the fire? and without adjustable shelving?

And I use a diffuser on every drum, every smoke.

N8man · Apr 28, 2014

I used a third for an extension on my drumpit, went with the no weld method using
a lid clamp to hold it all together....worked out well.....

Win nut · Apr 28, 2014

Do a Google search for Stan Johnson's magnum force smoker. I am in the process of building one, waiting on paint to arrive.

racedvl · Apr 28, 2014

Smokerking, what are you using in that second picture to put the thermometer through? I like the way that looks...

Ryan921 · Apr 28, 2014

I agree with SmokerKing on the door. It can really come in handy to get the temp up real quick, or just throwing extra chips/chunks on without pulling everything apart. Just be sure it gets sealed very well or it will cause great pain:x

Spyders03 · Apr 29, 2014

SmokerKing, that is a pretty hefty door system, I didn't think of something like that, although I may forego the door on my first build and keep that part simple, and try and get my airflow down good before expanding.

Looking at your beauty N8man, I may also forgo the addition seeing how tall it is, as I was planning on welding my top on, and that may make it too hard to access the inside. I'm getting the feeling I'm over-thinking things and trying to complicate things instead of just KISS.

I will be using dual temp gauges, and I did think about welding on some expanded metal on the side near the top for a workspace/shelf, just need to find a way to make it safe so a kid doesn't poke their eye out or cut themselves on a piece of metal sticking out.

SmokerKing · Apr 29, 2014

racedvl said:
Smokerking, what are you using in that second picture to put the thermometer through? I like the way that looks...

It's a conduit gland with rubber grommet, been on this forum for a while. Found at Home Depot or Lowes

SmokerKing · Apr 29, 2014

Ryan921 said:
I agree with SmokerKing on the door. It can really come in handy to get the temp up real quick, or just throwing extra chips/chunks on without pulling everything apart. Just be sure it gets sealed very well or it will cause great pain:x

:thumb: I've built 7 with the door in the side and they all seal fine. None have any gaskets on the door. The clamps help seal the door to the framed opening.

I hand pick out the steel for the door as most get warped during the shearing process at the steel yard.

N8man · Apr 29, 2014

Spyders03 said:
Looking at your beauty N8man, I may also forgo the addition seeing how tall it is, as I was planning on welding my top on, and that may make it too hard to access the inside.

it just looks tall when I'm not in the pix with it...:heh:

racedvl · Apr 30, 2014

Thank you smokerking, I have something to research now. I didn't know what to call it.

Spyders03 · May 2, 2014

Thanks for all the suggestions guys, I got to work on it some yesterday, and think I made some decent progress for my first one. I will get pics up soon

Modified UDS question

Spyders03

MemberGot rid of the matchlight.

Dadeo719

is one Smokin' Farker

mchar69

Quintessential Chatty Farker

ebijack

Babbling Farker

delarob

Knows what a fatty is.

SmokerKing

is One Chatty Farker

N8man

Babbling Farker

Win nut

Knows what a fatty is.

racedvl

Got Wood.

Ryan921

Knows what a fatty is.

Spyders03

MemberGot rid of the matchlight.

SmokerKing

is One Chatty Farker

SmokerKing

is One Chatty Farker

N8man

Babbling Farker

racedvl

Got Wood.

Spyders03

MemberGot rid of the matchlight.

Similar threads