|
Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking. |
|
Thread Tools |
10-04-2010, 12:15 PM | #6901 |
Got Wood.
Join Date: 09-29-10
Location: Mint Hill, NC
|
In the spirit of doing it cheap & simple, I was hoping there was a better option than buying a $40 mount from BBQ Guru.
Has anyone come up with their own design that was simple, effective, and cheap?? |
|
10-04-2010, 12:17 PM | #6902 |
Got Wood.
Join Date: 09-29-10
Location: Mint Hill, NC
|
|
|
10-04-2010, 01:41 PM | #6903 |
is Blowin Smoke!
Join Date: 09-07-10
Location: Chicago, IL - West burbs
|
I ran my UDS for the first time this weekend. I put 1 full webber charcoal chimney full of Kingsford in my basket. I piled it up around the outside edge of the 13" diameter basket to get a Minion method going. Then, I put 1/2 lit charcoal to fill up the middle. I put it in my UDS, and had temps at 200d nearly instantly. I close the vents and then slowly opened them as the temps steadied. It then chugged along around 240.
But, after about 5 hours, the temps started to fall off. I opened it up and saw that I still had a lot of charcoal around the edges, but the charcoal in the middle had all burned up. I shook the basket and knocked the coals into the middle and all was good - other then all the black smoke it made. Is there a preferred way to start the coals? I think this next time I'm going to skip putting the charcoal in the middle.
__________________
-Ryan Proudly Smoking on a UDS, PBC & Accidental Winner of the 2012 "Saucy" Throwdown. |
|
10-04-2010, 02:03 PM | #6904 | |
is Blowin Smoke!
Join Date: 09-07-10
Location: Sunny AZ
|
Quote:
|
|
|
10-04-2010, 06:55 PM | #6905 |
is one Smokin' Farker
Join Date: 09-15-10
Location: Tuscola Texas
|
Well you guys know how to make the wheels start turnin. I'm starting a uds now. I have the the fire cage built but the catch pan I'm using is off an old water heater. I have removed the paint from the hot side but the underside still has paint. Do I need to remove that paint also?
|
|
10-04-2010, 08:22 PM | #6906 | |
is one Smokin' Farker
Join Date: 03-05-09
Location: Seaford, NY
|
Quote:
__________________
[SIZE=3][COLOR=red][B]James [/B][/COLOR][/SIZE] [B]THE SMOKE 'N BARREL[/B] [COLOR=black][B]COMPETITION BBQ TEAM[/B][/COLOR][B] Seaford, NY[/B] Backwoods Party named Woody Weber One Touch Silver 22.5 (2x) Weber Smokey Mountain 18.5 (2x) Ugly Drum Smoker named Rusty [B][COLOR=red]Red[/COLOR][/B] Splash-Proof Super-Fast Thermapen [URL="http://www.thesmokenbarrel.blogspot.com/"]The Smoke 'N Barrel Blog[/URL] [URL="http://www.facebook.com/pages/The-Smoke-N-Barrel-Competition-BBQ-Team/124849310898216?v=wall#!/pages/The-Smoke-N-Barrel-Competition-BBQ-Team/124849310898216"]The Smoke 'N Barrel on Facebook[/URL] [URL="http://twitter.com/#!/thesmokenbarrel"]The Smoke 'N Barrel on Twitter[/URL] |
|
|
10-04-2010, 09:07 PM | #6907 |
is one Smokin' Farker
Join Date: 09-15-10
Location: Tuscola Texas
|
I'll do that. Next question is since I'll only have one grill. How far from the top do I need to put it?
Thanks in advance. I'd post pics but don't know how. All I get are red x's |
|
10-04-2010, 09:09 PM | #6908 |
Quintessential Chatty Farker
Join Date: 06-03-10
Location: Shawnee, KS
|
You want it at least 22-24" from the bottom of your charcoal basket. From there, if you just have a flat lid, I would try to put it down 8-10" to allow clearance for large butts or a turkey.
|
|
10-04-2010, 09:37 PM | #6909 | |
is Blowin Smoke!
Join Date: 09-07-10
Location: Chicago, IL - West burbs
|
Quote:
I'll try and level it off this next time, rather than all in the middle.
__________________
-Ryan Proudly Smoking on a UDS, PBC & Accidental Winner of the 2012 "Saucy" Throwdown. |
|
|
10-05-2010, 12:51 AM | #6910 |
Is lookin for wood to cook with.
Join Date: 08-16-09
Location: Costa Mesa CA
|
Quote:
You can get away with bolts on just one rack but I like the ability to swap out the racks mid cook top for bottom etc. I do some small catering gigs where I cook 3 shoulders per rack. The bottom rack would get done about 3 hrs sooner so now I swap halfway when I foil. The racks can be lifted out with ease. The bolts let the racks act as a stand/table with meat on the racks. I can quickly pull the racks and meat out and close the lid back up. I'll foil than swap rack positions. Having two levels of support bolts (bolted through the drum) doesn't allow for this since your bottom rack will get hung up on the top bolts. I also put my thermometer below the bottom rack. It again is just for looks. It runs about 40 degrees cooler at that level than the center of the top rack. Here I have a third rack that sits on the top rack. This will allow me to cook two to three racks of spares (St Louis) Rib tips go on the bottom rack. We cook 4 racks for competitions and this method allows me to cook em flat without a rib rack. I also foil ribs so again they can lay flat two racks per rack. This also works for chicken pieces. Here I have my third rack (rib rack) I used pure non plated steel bolts. Hardware total for two racks $5. Stanless steel will set you back $40. These bolts are coated with oil when you buy em to prevent rust. I got mine at Gnahl Lumber (So Cal). My rack bolts that go through the drum are stainless and all other hardware is stainless. I figured someone would ask about my basket set up so here are some picts. I also picked up a 2x20 aluminum cake pan at a local bake shop. You can also find em online. I’ve seen people use galvanized oil pans but that has led, and I’m kind of against my kids growing a tail. I used two kettle coal grates at 90 degrees. This is to hold lump better. If ya use briquettes I don’t think it’s necessary. I also have a container of used deep fry oil and a paint brush. I paint all metal after each cook with a coat of oil to keep the rust off. http://cooksdream.com/store/llprd202.html This has deffinatly become an addiction. What I love most is scoring higher than folks on $8000 cookers. These little things turn out (in my opinion) the best bbq. Thanks for viewing and sharing your's too. Most of all have fun!
__________________
" Happiness Is A Beer In One Hand And A Spatula In The Other " |
|
Thanks from:---> |
10-05-2010, 11:01 AM | #6911 |
On the road to being a farker
Join Date: 01-31-09
Location: Austin, Texas
|
I am not using a guru blower - so not sure the best method to put it on.
In the past I used a small pvc junction box - one of the small ones that connects conduit to conduit. I drilled out a hole on the side of the box for my fan and plugged up one of the conduit holes. I used a thread to pvc fitting to connect the box to my nipple. The fan was held in place with zip ties. It worked pretty good. The problem with connecting the blower to an existing nipple is that the fan hits one side of the fire basket. On warmer burns that will cause the basket to burn unevenly. I suspect if it every becomes a large enough annoyance you could build a small diffuser plate - or plumb to multiple nipples. My solution was to but the blower on the bottom, and use a full diffuser plate. |
|
10-05-2010, 12:08 PM | #6912 | |
Got Wood.
Join Date: 09-29-10
Location: Mint Hill, NC
|
Quote:
Right now, my best idea is to use a 1" ball valve for my main intake, and use a piece of bicycle inner tube rubber as a gasket of sorts to make a tight seal between the fan and the valve... if that makes sense. |
|
|
10-05-2010, 01:55 PM | #6913 |
Knows what a fatty is.
Join Date: 09-28-10
Location: katy, tx
|
@ mikeW
I see your concept and i really like it. I have couple of questions: 1. how many inches from the bottom for the 1st rack? 2. What are the sizes of the bolts between the racks? thanks for your information brunski... |
|
10-05-2010, 07:08 PM | #6914 |
On the road to being a farker
Join Date: 01-31-09
Location: Austin, Texas
|
When I was attached to a nipple, I was doing 2 things that were exaggerating the issue. One I was cooking hot (300-350 my tiny blower was giving all it had). The other was I was running with twigs instead of lump.
Current set up has an oversized blower that is restricted by the pipe bushing (did not have a spare close nipple). With the blower wide, it can keep an even fire burning in the basket (not that I would ever want to keep a fire burning while smoking - but it was a cool experiment). |
|
10-05-2010, 08:36 PM | #6915 | |
is one Smokin' Farker
Join Date: 07-08-09
Location: Datyona Beach, Fl
|
Quote:
Can we say that here???????. Paul B SS UDS |
|
|
Tags |
divided circle template, uds, ugly drum, ugly drum grill, ugly drum smoker |
|
|