|
Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking. |
|
Thread Tools |
04-28-2014, 08:28 AM | #1 |
somebody shut me the fark up.
Join Date: 08-22-13
Location: Fort Wayne, Indiana
|
High heat paint question
Ok i built a UDS rotisserie which will never have a cooking grate in it. I made it to run charcoal or small wood splits. My plan when using splits was to burn a couple of small ones down to coals and drop in a small split when necessary to maintain temps.
Here's my question...i used high heat 600 degree primer and then 900 degree caliper paint. That's plenty durable for say a basket full of red hot briquettes i just burned but I'm wondering if burning a couple of small splits in the charcoal basket would put off a bunch more heat than that. Basically i don't want to screw up my paint....i assume it'll be ok but am a tad apprehensive because i don't know how much hotter the splits will burn. Keep in mind it will be in a charcoal basket, lid will be off and it will only be one or two small ones. Thanks
__________________
Change the way you rotisserie for the BETTER![COLOR="Red"][B]Cajun Bandit Kits for your WSM or Weber Kettle Now Available![/B][/COLOR] Visit [COLOR="Red"]OctoForks[/COLOR] in Sales & Ventures Website & Blog: [url]www.octoforks.com[/url] |
|
04-28-2014, 09:03 AM | #2 |
is Blowin Smoke!
Join Date: 05-30-13
Location: Kyle, TX
|
From what I was told by my pit builder, it's always a good idea to slowly cure the paint with modest temps and then go to higher temps afterward. He uses three coats of a premium paint but says that if you go too high with it at first it could cause damage, even peeling for those who like to season their pits with 350 to 400 degree heat.
His advice was to let the cooker go at 225 for a few hours for the first fire. Then the next time, the paint will be cured enough to take high temps.
__________________
[FONT=Lucida Sans Unicode]Never Trust A Skinny Cook!!![/FONT] Lone Star Grillz Vertical Offset, New Braunfels Black Diamond Offset (Retired), Weber Kettle :grin: |
|
04-28-2014, 09:10 AM | #3 | |
somebody shut me the fark up.
Join Date: 08-22-13
Location: Fort Wayne, Indiana
|
Quote:
Well my first burn this weekend went up to 400* then the cook was in the 325* range...so i hope that would cure it. Any idea how much hotter two splits would burn then the red hot coals i used?
__________________
Change the way you rotisserie for the BETTER![COLOR="Red"][B]Cajun Bandit Kits for your WSM or Weber Kettle Now Available![/B][/COLOR] Visit [COLOR="Red"]OctoForks[/COLOR] in Sales & Ventures Website & Blog: [url]www.octoforks.com[/url] |
|
|
04-28-2014, 11:27 AM | #4 |
somebody shut me the fark up.
Join Date: 08-22-13
Location: Fort Wayne, Indiana
|
I'm thinking i'll just burn the splits down to coals outside of the drum and when they're burnt down to coals i'll set the basket inside the drum. Then i'll feed the fire one split at a time.....one shouldn't blister the paint.
__________________
Change the way you rotisserie for the BETTER![COLOR="Red"][B]Cajun Bandit Kits for your WSM or Weber Kettle Now Available![/B][/COLOR] Visit [COLOR="Red"]OctoForks[/COLOR] in Sales & Ventures Website & Blog: [url]www.octoforks.com[/url] |
|
04-28-2014, 11:35 AM | #5 |
is Blowin Smoke!
Join Date: 05-30-13
Location: Kyle, TX
|
Sounds like a plan!
__________________
[FONT=Lucida Sans Unicode]Never Trust A Skinny Cook!!![/FONT] Lone Star Grillz Vertical Offset, New Braunfels Black Diamond Offset (Retired), Weber Kettle :grin: |
|
|
|