MMMM.. BRISKET..
The BBQ BRETHREN FORUMS.  



Our Homepage Donation to Forum Overhead Welocme Merchandise Associations Purchase Subscription Amazon Affiliate
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking.


Reply
 
Thread Tools
Old 11-12-2009, 07:37 AM   #4471
EvilTwin v2
Found some matches.
 
Join Date: 11-11-09
Location: Moundsville, WV
Default

Quote:
Originally Posted by Babyboomerboy View Post
I bet you can cook some meat real fast at 800*
Oh yeah. Hook a leaf blower up to the intake & watch the drum start to glow!

At least it should be safe to cook in now.

I should have it painted today. I'm still trying to decide on a damper setup for the intake & exhaust.
EvilTwin v2 is offline   Reply With Quote




Old 11-12-2009, 07:57 AM   #4472
Typically
On the road to being a farker
 
Typically's Avatar
 
Join Date: 06-29-09
Location: NJ
Default

do you need a ladder to put the meat on?? :D that thing is gonna be a beast!!!!
__________________
drinkin' every drop from the bottom to the top!
1 UDS
Typically is offline   Reply With Quote


Old 11-12-2009, 10:54 AM   #4473
EvilTwin v2
Found some matches.
 
Join Date: 11-11-09
Location: Moundsville, WV
Default

Quote:
Originally Posted by Typically View Post
do you need a ladder to put the meat on?? :D that thing is gonna be a beast!!!!


It's only 5'2" at the top of the lid...just over 4' at the bottom of the lid.
EvilTwin v2 is offline   Reply With Quote


Old 11-12-2009, 01:37 PM   #4474
jetfxr27
is one Smokin' Farker
 
Join Date: 09-30-09
Location: Memphis
Default

That puts the U in Ugleeeeeeeee.
__________________
UDS', mUDS, COS. Weber gasser & kettle. Thermapen,Digiq2, Golden-Tiger
jetfxr27 is offline   Reply With Quote


Old 11-12-2009, 01:52 PM   #4475
jswordy
is one Smokin' Farker
 
jswordy's Avatar
 
Join Date: 05-13-09
Location: Fayetteville, TN
Default

bdon and others wondering when the liner is burned out enough:

When it is burned out enough, you should be able to use a pressure washer or take the drum to the helpie-selfie car wash and simply wash out the residue. You can tell it is ready if it is whitish or pinkish and flat, and if you can run your fingernail over the cooled barrel inside and scrap off paint.

The very best thing I have found to burn out liners is a Harbor Freight weed burner, which saves a lot of time, and which you will later use time and again as a jet engine method of starting your coals quickly, so go out and spend the $20 or whatever and get one. Just start burning around the inside of the barrel with that thing, and it will remove all the inside and outside coatings.
__________________
Double-Barrel Smoker (DBS); Ugly Drum Smoker (UDS)
jswordy is offline   Reply With Quote


Old 11-13-2009, 05:50 PM   #4476
SmokinAussie
somebody shut me the fark up.

 
SmokinAussie's Avatar
 
Join Date: 10-19-09
Location: Gold Coast, Queensland! (Finally Escaped Melbourne)
Name/Nickname : Bill
Default

Just joined from Australia... No such thing as a UDS here, and had never heard of one before....but plenty of Drums. Just checked around on eBay and it won't be long before I have got me a food grade drum. SO unless any other Aussies have done it, I think I'm gonna make the first UDS in Oz. I have a ship load of stuff to read in this thread first tho!
SmokinAussie is offline   Reply With Quote


Old 11-13-2009, 06:01 PM   #4477
Skidder
Babbling Farker
 
Join Date: 02-02-08
Location: Westfield,Ma.
Default

Evil that has to be one of the UGLIEST barrels yet. Nice job!! That thing is gonna put out some great bbq. Please post pics. Again nice work. I meant Ugly in a good way.
Skidder is offline   Reply With Quote


Old 11-14-2009, 02:35 AM   #4478
EvilTwin v2
Found some matches.
 
Join Date: 11-11-09
Location: Moundsville, WV
Default

Quote:
Originally Posted by Skidder View Post
Evil that has to be one of the UGLIEST barrels yet. Nice job!! That thing is gonna put out some great bbq. Please post pics. Again nice work. I meant Ugly in a good way.
Thanks!

There are 3 butts on it right now. I'll try to get some pics tomorrow as they come off.
EvilTwin v2 is offline   Reply With Quote


Old 11-14-2009, 11:04 AM   #4479
69cam
Found some matches.
 
Join Date: 11-11-09
Location: Tracy CA
Default

Hi to all.

Just wondering if a drum that used to contain water based latex paint, would be safe to use?

Thanks
Kevin
69cam is offline   Reply With Quote


Old 11-14-2009, 05:11 PM   #4480
QuietOne
Full Fledged Farker
 
Join Date: 09-18-09
Location: Fort Smith, NT
Default

One never knows what a drum is lined with and most are even if the lining is a thin coat of varnish or nukote or light plastic/BPA.

Drill some air holes 1" X 3 (4). Burn it HOT. Burn it LONG. Wash it scrub it and then Burn it again. Clean it up. Work it over with a knotted wire on angle grinder. Sander. Wire brush. Wash again. So that all the loose metal bits and abrasives go down the drain at the car wash.

Add a grate and charcoal basket. Coat the inside with lard. Fire it up. While the drum seasons play with Temp control. Let it run low for a bit then run it wide open and then slow it down. Hopefully closing everything down will put you out within 15 minutes or so. Find these things out before you start to cook.

Find where 210 -240 is on your air inlet(s). Mine it works out to 2 holes closed with magnets the one air inlet with the 1" ball valve little over 1/3 open. (My air inlets were drilled with a Irwin Uni-bit to 1 3/8")

Second run do it the same but you don't have to run it wide open, put a couple fatties on there, if something goes wrong you're not losing a lot.

Again work the temp control. I found that the Minion method and lighting 8 coals in the Weber lighter and putting in a small dent on the charcoal basket, dropping the coals on, that with the 2 holes uncovered and the gate valve wide it took about 25-35 mins to get the temperature climbing to 205 and I shut the two holes with magnets, at 210 I nudged the ball valve to 1/3 open. Drum went up to 240 and dropped to 230-215 for hours.

If I didn't lift the lid it stayed right there. Lift the lid the temp spikes up once all the way to 340F and I'd have to narrow down the valve so that the temp drops back down then open to 1/3 when it hits 235. I've found that if I close the ball valve for 5 mins then open the lid I don't get that spike or at least not so bad. (sorry my temps are in F(unny) degrees my turkey fryer therm is US temps though it's made in China)

Longest cook I've had so far was 10 hours at -10C and a pork loin roast that was to DIE for. Swear it was like "OH MY GOD. groan grunt smack smack, HANDS off it's mine" But then no pics so it didn't really happen.

Since I made my UDS I'm using it 3 - 5 times a week. I've gained 4 Kilos. Food coming off is so good one just eats more. Plus the fact that I'm cooking 5 Kg roasts and 4Kg butts and brining turkeys and chicken and pork loin and tenderloin and .... I've got to get a good vacuum sealer so I can freeze leftovers rather than FORCING (yeah right) myself to eat them.
QuietOne is offline   Reply With Quote


Old 11-14-2009, 09:41 PM   #4481
makizoo
Found some matches.
 
Join Date: 11-11-09
Location: Barre, MA
Default

4480 posts. Did it. Read 'em all. Do I get a t-shirt or sumthin'? Spent the day in the garage watching my barrel burn in the pouring rain. The build starts tomorrow.
makizoo is offline   Reply With Quote


Old 11-14-2009, 09:45 PM   #4482
Paul B
is one Smokin' Farker
 
Join Date: 07-08-09
Location: Datyona Beach, Fl
Default

Your only reward is now YOU have to post as much pron as you can.

Paul B
Paul B is offline   Reply With Quote


Old 11-15-2009, 07:05 AM   #4483
MushCreek
Full Fledged Farker
 
Join Date: 10-01-09
Location: Seminole Florida
Default

Now you can figure out how to incorporate everyone's suggestions, yet keep the weight of your drum under 500 lbs.!
__________________
I'm very intelligent, but I mask it by doing stupid stuff.
MushCreek is offline   Reply With Quote


Old 11-15-2009, 08:02 AM   #4484
Captain Dave
is one Smokin' Farker
 
Captain Dave's Avatar
 
Join Date: 07-29-09
Location: Luling, Texas 78648
Default

Why does everybody use 4 inlet holes? I never use the third or forth. Is there a reason?
__________________
Thanks for noticing
Captain Dave is offline   Reply With Quote


Old 11-15-2009, 08:18 AM   #4485
h20loo
is one Smokin' Farker
 
Join Date: 01-22-08
Location: waterloo ontario
Default

Quote:
Originally Posted by Captain Dave View Post
Why does everybody use 4 inlet holes? I never use the third or forth. Is there a reason?

Because they didn't make the first one big enough?
Four holes is good when you are burning the barrel, live in a cold climate and want to hit high temps for chicken or whatever or for the people who just need everything to be symetrical.
h20loo is offline   Reply With Quote


Reply

Tags
divided circle template, uds, ugly drum, ugly drum grill, ugly drum smoker

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ugly Drum Smoker ironslob Q-talk 2 09-19-2010 10:16 AM
Ugly Drum Smoker - Need Help Bartkowiakj Q-talk 10 06-18-2010 09:38 PM
One Ugly Drum Smoker Steve_B Q-talk 15 09-21-2009 10:32 PM
My (not-so) Ugly Drum Smoker. hav Q-talk 47 11-05-2008 02:30 PM
Ceramic Cooker Meets Ugly Drum Smoker - BUDCS - Concept Drum Discussion Hook_Line_and_Sinker Q-talk 9 04-26-2008 02:24 PM

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Forum Custom Search: Enter your Search text below. GOOGLE will search ONLY the BBQ Brethren Forum.
Custom search MAY not work(no display box) in some configurations of Internet Explorer. Please use compliant version of Firefox or Chrome.







All times are GMT -5. The time now is 04:37 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts