iQue on Char-Griller Kamado

smokeyw · Apr 13, 2012

Has anyone tried a Pitmaster iQue on a CGK? I use one on my UDS and it does a fantastic job. However, I'm afraid it may be a little too powerful for the CGK. For this reason, I am considering adding a dedicated port for it with a ball valve so that I can restrict the air flow as needed. I would just drill a hole in the ash pan and mount the necessary hardware kind of like we do on a UDS. Has anyone tried this or any thoughts on this?

Vision · Apr 13, 2012

I believe the newer ones come with a washer in the exhaust end, that should restrict the flow a little.

smokeyw · Apr 13, 2012

Yes, the new ones do have the washer. My 2nd one came with that. But I was thinking if you had a dedicated port with a ball valve, you would have even more control. An added benefit would be not having to change the lower draft door. If you didn't want to use the iQue you could just close the ball valve and use the original slide control.

andy_christy · Apr 13, 2012

I use one on mine. Use the washer & cover all but 2 or 3 of the intake holes. Works great.

smokeyw · Apr 13, 2012

What type of port do you use to connect the hose? Do you have a dedicated port or the lower vent control adapter?

andy_christy said:
I use one on mine. Use the washer & cover all but 2 or 3 of the intake holes. Works great.

andy_christy · Apr 13, 2012

smokeyw said:
What type of port do you use to connect the hose? Do you have a dedicated port or the lower vent control adapter?

I orderd a vent adapter for a lg BGE & ground it down to fit.

captndan · Apr 14, 2012

I thought about putting it on the ash pit but not sure if it would blow up the ash. I'll be looking at the options.

John I. Que · Apr 24, 2012

The newest version (just began shipping) has an adjustable air intake damper to take the place of the washers (http://www.youtube.com/watch?v=yxU3WYLwUB0). I have not tested it yet on a CGK, but it works very well on my Primo Kamado. The intake damper setting #1 is designed to work with the smallest, most efficient pits like BSKs. I suspect the BSK is even more efficient than the CGK, so it should be fine.

JS-TX · Apr 24, 2012

captndan said:
I thought about putting it on the ash pit but not sure if it would blow up the ash. I'll be looking at the options.

I think it would blow up ash, not a good area for a dedicated port IMO.

smokeyw · Apr 24, 2012

I used a pipe cap with two 1/4" holes so that the air is angled back toward the side. It blows absolutely no ash.

JS-TX said:
I think it would blow up ash, not a good area for a dedicated port IMO.

captndan · Apr 25, 2012

I put mine on the back side opposite the vents. Only thru the outer skin so the air must go around inside to come out the vents. No ash works like a charm.

smokeyw · Apr 25, 2012

Good idea :thumb:

captndan said:
I put mine on the back side opposite the vents. Only thru the outer skin so the air must go around inside to come out the vents. No ash works like a charm.

---k--- · Apr 25, 2012

John I. Que said:
The newest version (just began shipping) has an adjustable air intake damper to take the place of the washers (http://www.youtube.com/watch?v=yxU3WYLwUB0). I have not tested it yet on a CGK, but it works very well on my Primo Kamado. The intake damper setting #1 is designed to work with the smallest, most efficient pits like BSKs. I suspect the BSK is even more efficient than the CGK, so it should be fine.

John, thanks for posting that video. It was interesting to see how much you're blocking compared to the old ones. I have a piece of tape blocking a third of my intake. But, since it has started to warm up and I haven't taken the insulation blanket off my drum, I've been noticing that it is running hot and taking longer to cool down. Seeing that video gives me a much better idea of how much I should be blocking off.

speedrcer1 · Apr 25, 2012

John I. Que said:
The newest version (just began shipping) has an adjustable air intake damper to take the place of the washers (http://www.youtube.com/watch?v=yxU3WYLwUB0). I have not tested it yet on a CGK, but it works very well on my Primo Kamado. The intake damper setting #1 is designed to work with the smallest, most efficient pits like BSKs. I suspect the BSK is even more efficient than the CGK, so it should be fine.

I recently used an original iQue 110 with the washer installed on a Bubba Keg.
I cleaned it out fully. Put a full chimney of royal oak in. (unlit) Added about a 1/4 chimney of lit coals. Set the iQue at 225. Top vent just open a crack.
Kept it like a rock.
Cooked 2 bone in pork shoulders to tender goodness in about 12 hours. (no refueling)
So I decided to let it continue and see how long it could keep temp.
17 hours. Amazing.
I love my iQue.

speedrcer1 · Apr 25, 2012

Oh, one other quick note. I find if the iQue is above the level of the fire. Smoke will come out of it when the fan is not running. Thus smoke not going up to the meat. So I keep it on the ground under the keg.
I would expect the same on a well sealed CG Kamado.

iQue on Char-Griller Kamado

smokeyw

is Blowin Smoke!

Vision

is Blowin Smoke!

smokeyw

is Blowin Smoke!

andy_christy

Guest

smokeyw

is Blowin Smoke!

andy_christy

Guest

captndan

Quintessential Chatty Farker

John I. Que

Knows what a fatty is.

JS-TX

is One Chatty Farker

smokeyw

is Blowin Smoke!

captndan

Quintessential Chatty Farker

smokeyw

is Blowin Smoke!

---k---

is One Chatty Farker

speedrcer1

is Blowin Smoke!

speedrcer1

is Blowin Smoke!

Similar threads