oink
The BBQ BRETHREN FORUMS.  


Our Homepage Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners(temp offline)
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
 
Thread Tools
Old 04-14-2008, 06:43 PM   #1
boatnut
is One Chatty Farker
 
boatnut's Avatar
 
Join Date: 03-22-05
Location: Ohio
Default How to adapt Weber kettle lid to UDS??

Ok, was out in garage measuring stuff. looks like the outside measurement on weber kettle "lip" is 22 5/8". The inside measurement of the drum appears to be 22 1/2". do i just take a cut of blade in my grinder and cut off about an inch of the kettle then slide it down into the drum till it snugs up? do i need to weld it? would like option of using both flat lid as well as kettle lid for hams/turkeys etc. Another option I think I have would be to weld the kettle lid to a spare flat lid then cut out the inside of the flat lid leaving about an inch "flange" all around.
Can anyone chime in???
__________________
Mike

GOSM smoker (gas)
Masterbuilt (electric)
Weber Kettle
Weber Gasser (2)
Weber WSM


I'd rather have a bottle in front of me then a frontal lobotomy
boatnut is offline   Reply With Quote


Old 04-14-2008, 06:48 PM   #2
JD McGee
somebody shut me the fark up.
 
JD McGee's Avatar
 
Join Date: 06-28-07
Location: Duvall, WA
Default

???...a 22 1/2 in Weber kettle lid fits perfectly on top of my 55 gallon drums. Swamprb has done a similar mod to his drums...I'm sure he'll chime in or you can sort through his drum mod posts...if you have a few days to kill!
__________________
Wine Country "Q" Competition BBQ Team
PNWBA Team Of The Year 2011, 2012, 2013, & 2014
Proudly sponsored by Kosmo's Q, MAK Grills, BBQr's Delight, and Ravenswood Winery!
JD McGee is offline   Reply With Quote


Old 04-14-2008, 06:58 PM   #3
bertkemtncurs
On the road to being a farker
 
Join Date: 10-04-06
Location: Cardington, OH , Buckeye Country
Default

Never thought about welding the dome to a flat lid and cutting it out - good idea!
__________________
UDS
GOSM
modified ECB
22.5" kettle
18.5" Weber
Stainless gasser
bertkemtncurs is offline   Reply With Quote


Old 04-14-2008, 07:23 PM   #4
swamprb
somebody shut me the fark up.
 
swamprb's Avatar
 
Join Date: 10-27-06
Location: Bothell WA
Default

Flange mod! I do this for the open drums with lids, it allows me to use both lids. But one thing I have noticed using a Weber lid without the flange on closed drums is that they leak greasy condensation down the sides of the drums. With the flange it does not.

Closed drum with top cut out and kettle flange







Open top drum with flange in place





Flange removed and drum lid in place



I use a cut off tool on the kettle
__________________
Brian - Left Hand Smoke BBQ PNWBA 2010 Team of the Year
BGE's/WSM's/Pellet Pro WSM/BWS Gater/BDS Clones/Cookshack 008/Weber Performer w EZ-Que/Cajun Bandit/Rib-O-Lator Test Pilot/La Caja China/BBQ Guru/Weber 1000 RK Drum Coffee Roaster
Follow Left Hand Smoke on Facebook!http://www.facebook.com/pages/Left-H...462391?sk=wall
KCBS CBJ/PNWBA CBJ www.pnwba.com
swamprb is offline   Reply With Quote


Old 04-14-2008, 07:34 PM   #5
boatnut
is One Chatty Farker
 
boatnut's Avatar
 
Join Date: 03-22-05
Location: Ohio
Default

swamp,
you da man...thanks for da quick response. gotta love this place. so looks like you cut maybe 1 1/2" off the weber kettle for the flange? and it just sits inside the drum. do you get much leakage around it or does it seal pretty tight? gonna have to get to work.
__________________
Mike

GOSM smoker (gas)
Masterbuilt (electric)
Weber Kettle
Weber Gasser (2)
Weber WSM


I'd rather have a bottle in front of me then a frontal lobotomy
boatnut is offline   Reply With Quote


Old 04-14-2008, 07:39 PM   #6
Single Fin Smoker
is One Chatty Farker
 
Single Fin Smoker's Avatar
 
Join Date: 10-11-06
Location: Huntington Beach California
Default

Just do like Swamp says. I did and it works great. Your kettle ring just slides right in nice and snug without any welding.
I tried using some oven gasket(which worked pretty good), but it kept falling apart on me.

Oh yeah, I do notice that if I use another lid(other than the original) it does pull up a little bit when I take it off.
__________________
Sidartha translated: Every wish fullfilled
Keiki Kai
UDS(Norco II)
WSM
Webber Kettle
True stainless kegerator w/cheap 1/2 barrel
10'6 EC single fin
10' Minchington 2-1 set up
Single Fin Smoker is offline   Reply With Quote


Old 04-14-2008, 08:28 PM   #7
swamprb
somebody shut me the fark up.
 
swamprb's Avatar
 
Join Date: 10-27-06
Location: Bothell WA
Default

Quote:
Originally Posted by boatnut View Post
swamp,
you da man...thanks for da quick response. gotta love this place. so looks like you cut maybe 1 1/2" off the weber kettle for the flange? and it just sits inside the drum. do you get much leakage around it or does it seal pretty tight? gonna have to get to work.
On the open drums none of mine are the same, I ran a bead of Permatex Hi-temp silicone around them and virtually no leakage. If you put them in the closed drum top no leaks. I used a rotisserie ring on mine and the only leaks were around the spit rod cutouts.



This is my "Patio Model" and you can see how the flange just sits on the lip of the drum, the red bead is the silicone and it does a great job.
__________________
Brian - Left Hand Smoke BBQ PNWBA 2010 Team of the Year
BGE's/WSM's/Pellet Pro WSM/BWS Gater/BDS Clones/Cookshack 008/Weber Performer w EZ-Que/Cajun Bandit/Rib-O-Lator Test Pilot/La Caja China/BBQ Guru/Weber 1000 RK Drum Coffee Roaster
Follow Left Hand Smoke on Facebook!http://www.facebook.com/pages/Left-H...462391?sk=wall
KCBS CBJ/PNWBA CBJ www.pnwba.com
swamprb is offline   Reply With Quote


Old 04-14-2008, 08:46 PM   #8
BobBrisket
Moderator
 
BobBrisket's Avatar
 
Join Date: 12-11-07
Location: El Paso, TX
Default

Swamprb's is right about them all being different. My drum was banded and when I dropped the flange in...................it dropped all the way into the drum. I had to cut the center out of the drum lid and then use the lip that was left over along with the band in order to allow the flange to fit. I also cut the flange a little lower so that I could continue to use the grate tabs. Good luck on you build and keep the pron coming.
http://www.bbq-brethren.com/forum/sh...t=drum+is+done
__________________
UDS, Pit Barrel Cooker-Courtesy of Poobah, WSM, 22.5 Weber Kettles-A, K, DR Stamped, 18.5 Weber Bar-B-Kettle, Weber 18.5 Smokey Joe Platinum, Weber Genesis Silver B, Lil' Chief Smoker, Lodge Sportman Grill, Backyard Fire Pit, Dutch Ovens, Discada Set Up!
BobBrisket Jr.-MUDS, WSJ Silver
My BEST Compliment......"You're a good cooker, Dad!"--My Son :)
Miss You, Marty! RIP
BobBrisket is online now   Reply With Quote


Old 04-15-2008, 02:18 AM   #9
Single Fin Smoker
is One Chatty Farker
 
Single Fin Smoker's Avatar
 
Join Date: 10-11-06
Location: Huntington Beach California
Default

I just cut those little handle dealys off.
__________________
Sidartha translated: Every wish fullfilled
Keiki Kai
UDS(Norco II)
WSM
Webber Kettle
True stainless kegerator w/cheap 1/2 barrel
10'6 EC single fin
10' Minchington 2-1 set up
Single Fin Smoker is offline   Reply With Quote


Old 04-15-2008, 10:45 AM   #10
Beerwolf
Take a breath!
 
Beerwolf's Avatar
 
Join Date: 06-03-07
Location: Cloverdale, Ca
Default

You guys are too complicated.... Just take a crescent wrench to the webber lid, barely open the wrench and use it to bend out the lip. You will have to do this about every 1/2 inch or so as you go around the lip, it wont even break the paint and its a lot better than thrashing a good webber kettle bottom which can be used later as a redneck fire pit
__________________
"Assumption is the Mother of all F___ups!"
Beerwolf is offline   Reply With Quote


Old 01-19-2010, 09:59 AM   #11
CircleW
On the road to being a farker
 
CircleW's Avatar
 
Join Date: 07-02-09
Location: New England
Default

Beerwolf, could you post a pic of your method? I finally got a Weber lid and it is about 1/2in too small for my drum. I don't want to cut up the bottom of the Weber for a flange... Does your method seal well? Any problems?

Thanks!
CircleW is offline   Reply With Quote


Old 01-19-2010, 10:29 AM   #12
T-Bird
Found some matches.
 
Join Date: 01-12-10
Location: Ardmore, TN
Default

First drum I got was 22 3/4" diameter, Weber lid wouldn't fit. Second drum was 22 1/2", Weber lid fits like it was made for it...
T-Bird is offline   Reply With Quote


Old 01-19-2010, 11:01 AM   #13
Phubar
somebody shut me the fark up.
 
Join Date: 04-24-09
Location: Utrecht,TheNetherPharkinglands
Default

Quote:
Originally Posted by T-Bird View Post
First drum I got was 22 3/4" diameter, Weber lid wouldn't fit. Second drum was 22 1/2", Weber lid fits like it was made for it...

My donor Weber 22,5" fits perfectly on my UDS.
Recently I scored a 2nd hand Weber 18,5" for my Midi UDS.
After seeing your drum yesterday I decided to go further with mine.
The lid doesn't fit perfectly like the 22,5" lid does on the yellow UDS but I made a phonecall today to the place that welded my charcoal basket,gonna drop by tomorrow morning to let them fabricate a charcoal basket again and see if they can make my lid fit.
I do have a smaller barrel where the Weber lid fits perfectly on the drum lip so probably I'm gonna take that drum with me just in case so if needed they can cut the lip of the drum and weld it to the lip of the midi drum.
Probably gonna ask them first if they can do something to the lip like make it thinner/flatter.



__________________
-TG
-WGA (3)
-UDS (S,M,L)

All fueled by [COLOR=lime]Ecobrasa[/COLOR] Coco Briquettes

*[URL="http://lowlandsmokers.blogspot.com/2011/06/lowland-smokers-workshop-hei-en-boeicop.html"]Lowland Smokers[/URL] Dutch BBQ Champion 2011 - 2012*
*[URL="http://lowlandsmokers.blogspot.com/2011/06/lowland-smokers-workshop-hei-en-boeicop.html"]Lowland Smokers[/URL] Dutch BBQ Champion 2013 Low 'n Slow
*WGA Ambassador
Phubar is online now   Reply With Quote


Old 01-19-2010, 11:11 AM   #14
MushCreek
Full Fledged Farker
 
Join Date: 10-01-09
Location: Seminole Florida
Default

I've made 2 UDS so far, and both were just a tad big for a Weber lid. I added a band of metal around the inside. On my stainless UDS, I bolted it. On the steelie, I welded it ever few inches. Both work well. I was going to seal it with silicon, but it doesn't seem necessary.
__________________
I'm very intelligent, but I mask it by doing stupid stuff.
MushCreek is offline   Reply With Quote


Old 01-19-2010, 11:14 AM   #15
Rich Parker
Babbling Farker

 
Rich Parker's Avatar
 
Join Date: 06-20-09
Location: Grand Rapids, MI
Default

Quote:
Originally Posted by Beerwolf View Post
You guys are too complicated.... Just take a crescent wrench to the webber lid, barely open the wrench and use it to bend out the lip. You will have to do this about every 1/2 inch or so as you go around the lip, it wont even break the paint and its a lot better than thrashing a good webber kettle bottom which can be used later as a redneck fire pit
^^^what he said.

I used channel locks and bent the rim of the lid out, set it on the drum, and persuaded it back in place with a rubber hammer. Perfection!
__________________
WSM, UDS, Deep South Medium, and Deep South GC28 - iBQ'n BBQ Team co-owner TheBBQSuperstore.com sponsored by Deep South Smokers
Rich Parker is online now   Reply With Quote


Thanks from:--->
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
UDS Weber kettle lid mod help Tricky Q-talk 20 11-26-2011 03:32 PM
Weber Kettle Lid Question JiveTurkey Q-talk 21 12-23-2009 06:06 AM
Raising the Lid of my Weber Kettle paperboy98 Q-talk 10 06-13-2009 09:44 AM
Weber kettle lid Panther5150 Q-talk 5 01-27-2009 08:58 PM

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Forum Custom Search: Enter your Search text below. GOOGLE will search ONLY the BBQ Brethren Forum.





All times are GMT -5. The time now is 12:26 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts