拉猪肉
The BBQ BRETHREN FORUMS.


Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
 
Thread Tools
Old 11-02-2013, 03:57 PM   #1
RClark115
Got Wood.
 
Join Date: 10-13-13
Location: Anaheim, ca
Default My UDS Build, and questions

Working on burning out my 55 gallon drum, for my UDS. As you can see I have removed a lot of the outer paint. I don't think I'm out of the woods yet with the red liner though. I have burned two pallets in it so far, and this is where I am. I can keep putting pallets, but right now I have a pile of smoldering wood in the bottom, covering the intakes. I'm not sure that puting more pallets in is going to get me any further at this point. Should I let the wood burn through and dump it out to go again? Or just keep adding wood and end up with a half barrel of smoldering wood?


RClark115 is offline   Reply With Quote


Old 11-02-2013, 04:07 PM   #2
ajstrider
is One Chatty Farker
 
Join Date: 09-02-12
Location: Kentucky
Default

I would keep putting more in, those inlets on the bottom don't do much for this style of fire. It gets its air from the top. Think of all the people that burn trash in drums, they have no intakes on the bottom. Plenty of people burn first, then put on intakes. Just be mindful of hot ash coming out of those intakes now, cap them off if you have any.
__________________
XL Big Green Egg, Weber kettles, WSM 22.5" and Pellet Pro adapter
ajstrider is offline   Reply With Quote


Old 11-02-2013, 04:39 PM   #3
Fwismoker
somebody shut me the fark up.

 
Fwismoker's Avatar
 
Join Date: 08-22-13
Location: Fort Wayne, indiana
Default

Let the fire die and use angle grinder wire brush...wipe down and season.
__________________
New Addition![/B] Dedicated stick burning/charcoal UDS Rotisserie!,
Lou -Mini WSM uds style,
Jaime- Jumbo mini or Jimmy (YES it's better than your PBC! )
Black bullet -newly renovated Big Poppa Black powder coated UDS,
Jaime build- http://www.bbq-brethren.com/forum/sh...d.php?t=173767
Fwismoker is offline   Reply With Quote


Old 11-02-2013, 04:44 PM   #4
SmittyJonz
somebody shut me the fark up.
 
SmittyJonz's Avatar
 
Join Date: 07-17-13
Location: Burleson Tx
Default

I burnt my red liner out with a HOT. 4 hr fire. Then still had to wire wheel it( liner was Blistered/ flaking off but not gone)
__________________
FARKING N Tx LATE Spring Bash May 30th - at Peep's House.
SmittyJonz is online now   Reply With Quote


Old 11-02-2013, 04:44 PM   #5
c farmer
Babbling Farker

 
c farmer's Avatar
 
Join Date: 06-13-13
Location: pa
Default

I got a flapper style wheel for my angle grinder at lowes that worked good for me.
__________________
Adam

Gold mini wsm 1st gen mes, amazin dust and pellet smoker, and the uds.
c farmer is online now   Reply With Quote


Thanks from:--->
Old 11-02-2013, 05:33 PM   #6
RClark115
Got Wood.
 
Join Date: 10-13-13
Location: Anaheim, ca
Default

it appears during the burn I warped my lid. While it is frustrating, guess I will have to see if the weber fits
RClark115 is offline   Reply With Quote


Old 11-02-2013, 05:38 PM   #7
Fwismoker
somebody shut me the fark up.

 
Fwismoker's Avatar
 
Join Date: 08-22-13
Location: Fort Wayne, indiana
Default

Quote:
Originally Posted by RClark115 View Post
it appears during the burn I warped my lid. While it is frustrating, guess I will have to see if the weber fits
Ugh i was gonna warn you about that. Flat lids are a dime a dozen tough.
__________________
New Addition![/B] Dedicated stick burning/charcoal UDS Rotisserie!,
Lou -Mini WSM uds style,
Jaime- Jumbo mini or Jimmy (YES it's better than your PBC! )
Black bullet -newly renovated Big Poppa Black powder coated UDS,
Jaime build- http://www.bbq-brethren.com/forum/sh...d.php?t=173767
Fwismoker is offline   Reply With Quote


Old 11-02-2013, 05:40 PM   #8
c farmer
Babbling Farker

 
c farmer's Avatar
 
Join Date: 06-13-13
Location: pa
Default

Quote:
Originally Posted by RClark115 View Post
it appears during the burn I warped my lid. While it is frustrating, guess I will have to see if the weber fits

I did the same thing.
__________________
Adam

Gold mini wsm 1st gen mes, amazin dust and pellet smoker, and the uds.
c farmer is online now   Reply With Quote


Old 11-02-2013, 05:48 PM   #9
Fwismoker
somebody shut me the fark up.

 
Fwismoker's Avatar
 
Join Date: 08-22-13
Location: Fort Wayne, indiana
Default

Quote:
Originally Posted by c farmer View Post
I did the same thing.
Yea i was gonna warn you also.... my bad
__________________
New Addition![/B] Dedicated stick burning/charcoal UDS Rotisserie!,
Lou -Mini WSM uds style,
Jaime- Jumbo mini or Jimmy (YES it's better than your PBC! )
Black bullet -newly renovated Big Poppa Black powder coated UDS,
Jaime build- http://www.bbq-brethren.com/forum/sh...d.php?t=173767
Fwismoker is offline   Reply With Quote


Old 11-02-2013, 05:51 PM   #10
RClark115
Got Wood.
 
Join Date: 10-13-13
Location: Anaheim, ca
Default

Quote:
Originally Posted by Fwismoker View Post
Ugh i was gonna warn you about that. Flat lids are a dime a dozen tough.
So then do u just take a wire wheel to the lid usually?
RClark115 is offline   Reply With Quote


Old 11-02-2013, 05:56 PM   #11
Fwismoker
somebody shut me the fark up.

 
Fwismoker's Avatar
 
Join Date: 08-22-13
Location: Fort Wayne, indiana
Default

Quote:
Originally Posted by RClark115 View Post
So then do u just take a wire wheel to the lid usually?
I'd say just a weed burner and wire wheel. I have a metal recyler by me i can get 50 lids a week if i wanted...look around for one. Call up the recyclers and ask them if they have 50 gallon drums coming through to get a replacement.
__________________
New Addition![/B] Dedicated stick burning/charcoal UDS Rotisserie!,
Lou -Mini WSM uds style,
Jaime- Jumbo mini or Jimmy (YES it's better than your PBC! )
Black bullet -newly renovated Big Poppa Black powder coated UDS,
Jaime build- http://www.bbq-brethren.com/forum/sh...d.php?t=173767
Fwismoker is offline   Reply With Quote


Old 11-02-2013, 05:59 PM   #12
Bludawg
somebody shut me the fark up.
 
Bludawg's Avatar
 
Join Date: 07-04-09
Location: Jonesboro,Tx
Default

live & learn buy an unlined drum you'd be burnin meat right now
__________________
I never met a Cow that I didn't like with a little Salt & Pepper! Certified PORK-A-HOLIC
Bludawg is online now   Reply With Quote


Old 11-02-2013, 06:00 PM   #13
Teleking
is One Chatty Farker
 
Join Date: 11-10-08
Location: Maine
Default

Quote:
Originally Posted by ajstrider View Post
I would keep putting more in, those inlets on the bottom don't do much for this style of fire. It gets its air from the top. Think of all the people that burn trash in drums, they have no intakes on the bottom. Plenty of people burn first, then put on intakes. Just be mindful of hot ash coming out of those intakes now, cap them off if you have any.
Really! Please explain the draft process that does not benefit from air and heat rising.
Teleking is offline   Reply With Quote


Old 11-02-2013, 06:08 PM   #14
Gettinit
On the road to being a farker
 
Join Date: 10-27-13
Location: Thomasville NC
Default

Mine had glue in the drums. I hope a match will get rid of the glue. No idea what the liner may be, if any.

I saw pics with drums upside down and with a part of another drum clamped to a drum. Any real benefits?
Gettinit is offline   Reply With Quote


Old 11-02-2013, 06:21 PM   #15
RClark115
Got Wood.
 
Join Date: 10-13-13
Location: Anaheim, ca
Default

Quote:
Originally Posted by SmittyJonz View Post
I burnt my red liner out with a HOT. 4 hr fire. Then still had to wire wheel it( liner was Blistered/ flaking off but not gone)
Like this?
RClark115 is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 12:25 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.