ブタ
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 07-17-2013, 10:54 AM   #31
pitbossJB
is one Smokin' Farker

 
pitbossJB's Avatar
 
Join Date: 12-05-09
Location: Albuquerque,N.M.
Downloads: 0
Uploads: 0
Default

Sweet!! Nice job.
__________________
"It's all done with smoke and mirrors..............I think I like smoke the best"

UDS
Highly modified Bandera w/ griddle on firebox
Mini SJ/UDS
Smokey Joe's
pitbossJB is offline   Reply With Quote


Thanks from:--->
Unread 07-17-2013, 10:54 AM   #32
Tsevg9
On the road to being a farker
 
Tsevg9's Avatar
 
Join Date: 05-02-13
Location: Saint Louis, MO
Downloads: 0
Uploads: 0
Default

Looks sweet! If you ever feel like making another, I can take this off your hands for ya.
__________________
Learning the ropes of BBQ, built my first UDS and have a few butts under my belt
Tsevg9 is offline   Reply With Quote


Thanks from:--->
Unread 07-17-2013, 11:51 AM   #33
Twelvegaugepump
is one Smokin' Farker

 
Join Date: 08-21-11
Location: Menasha, WI
Downloads: 1
Uploads: 0
Default

Thanks Smokin. Did you do the sandblasting or a shop? How many hours of effort. I am pricing sandblasting and it is very expensive in these parts!
__________________
KCBS Certified Judge
Weber Gasser
Weber 18" circa 1965
2 22" Weber Silvers and 1 22" Weber Gold
King Pig UDS
Tejas Charcoal 2452 Grill, 28" discada
Char Griller King Kamado
1 Smokey Joe and 1 Mini WSM
Currently building a 22' Portable Kitchen [URL="http://www.bullybbq.com"]www.bullybbq.com[/URL]
Twelvegaugepump is offline   Reply With Quote


Unread 07-17-2013, 04:21 PM   #34
Smokin' Greene
On the road to being a farker

 
Join Date: 07-12-12
Location: TX
Downloads: 0
Uploads: 0
Default Modification and Changes

This the basket modification for the minion effect. Works good. I did not make 3 dividers like some people do.
basket modification.jpg

I modified the upper cooking surface after cooking a few times. It was always in the way when cooking on the bottom grates. I cut 6" off.
right lid.jpg

cooking grates.jpg

I modified the ET counter weights. Doors weighed 27# they needed counter weights. The bend in the neck was to shorten the fold back position. They have a nice fluid movement. Not too heavy but wont come open going down the road. I found a very helpful calculation on the internet may have even been on the forum.
Lids.jpg

lids 3.jpg

Modified hinges. First generation hinges real nice laser cut hinges looked great, but function was not what I wanted. The doors were not very fluid and smooth. I actually had to rebuild the doors completely. I had a piece of pipe left over. The 1st doors sprung about a .25" at the bottom and I got carried away with trying to pull them in and warped them pretty bad. So I started over and rebuilt the hinges at the same time. It was a time consuming loss, but turned out better in the end.
hinges.jpg

I also changed the handles at this time to. Laser cut pieces with a down turn to help with that hot wrist/edge of door potential problem. The handles are solid stock 1 1/4" aluminum drilled and tapped.

handles.jpg

Finally Inlet Modification: After first two trial runs I did not like the temperature across the bottom grates. As you can see in the 1st picture I used a inverted inlet that pushed the heat upward, but the bottom of the pit remained cool. After visiting the bbq calculator I realized the inlet was not big enough for cooking chamber. So, I cut 2-2.5" hole below the other inlet and build a removable deflector plate and it worked like a charm. Even temp al the way across. I cooked 2 5# beef rib roast on the far end and 2 racks of baby back pork ribs closest to the fire box. I had a digital thermometer for both side same temp across pit.
inlet.jpg

inlet 5.jpg

inlet inside.jpg
__________________
Smokin' Greene
Smokin' Greene is offline   Reply With Quote


Thanks from:--->
Reply

Tags
horizontal, Insulated, insulated smoker, offset, stick burner, trailer, trailer build

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 07:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts