喫煙者
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 05-12-2013, 08:19 PM   #16
Daggs
Full Fledged Farker
 
Join Date: 09-09-12
Location: Crystal Lake IL
Downloads: 0
Uploads: 0
Default

Quote:
Originally Posted by WineMaster View Post
Foil dont = Pot Roast
Not knowing how to use it does.
^^^
I only use butcher paper and that's only once in a while when I'm having people over that don't like bark.
__________________
UDS (not so U) UDD, 22.5 OTS, Coming soon: mini UDS & double barreled RFS
Daggs is offline   Reply With Quote


Unread 05-12-2013, 09:14 PM   #17
jmoney7269
Banned
 
jmoney7269's Avatar
 
Join Date: 02-07-11
Location: brenham, texas
Downloads: 0
Uploads: 0
Default

Quote:
Originally Posted by Q*bert View Post
-Since I'm cooking on an UDS the fat cap was down to provide a heat shield. Should I put a deflector underneath & cook fat up??
Heck no! If you put in a deflector, Your taking away the flavor that uds's are know for. I like to get a little char flavor on both sides. It don't get no more simple than this:
Fat side up 2 hrs@300
Fat side down 2 hrs @300
Check temp to see it its @180, if not continue to cook.
Wrap @180, check temp again around 205-210 to see its probing like buttah. Temp don't mean diddly squat, it's when she decides to give it up, that's when it gets good! We are talkin about brisket still
jmoney7269 is offline   Reply With Quote


Thanks from:--->
Unread 05-13-2013, 07:21 AM   #18
Q*bert
On the road to being a farker

 
Join Date: 07-28-11
Location: Westminster, MD
Downloads: 0
Uploads: 0
Default

Quote:
Originally Posted by WineMaster View Post
Foil dont = Pot Roast
Not knowing how to use it does.

What's the best way?
Since I'm new to brisket, I'll take any know how you're willing to share.
Thanks
__________________
Astro Pigs BBQ
Our mission on Earth is to make BBQ that's out of this world

http://www.facebook.com/AstroPigs
KCBS MABA

Proudly Sponsored By:
The BBQ Equipment Store http://http://www.bbqequipmentstore.com/
K-Coast Surf Shop http://www.kcoast.com/
J.O. Spice Company Inc. http://www.jospices.com/
Q*bert is offline   Reply With Quote


Unread 05-13-2013, 09:06 AM   #19
Teltum
On the road to being a farker
 
Join Date: 03-26-13
Location: Barberton, Ohio
Downloads: 0
Uploads: 0
Default

I ran a brisket this weekend.

I like how yours looked, one thing I did different was I did not foil.

Until you get past your stall don't foil (unless you are in hurryup mode foil will accelerate the cook though the stall). My understanding of the stall is that there is a lot of water in meat and the stall is the meat "sweating" this water out. This condenses the brisket flavor, where the foil before the stall traps the moisture and turns brisket into roast beef. The moisture in a brisket is the rendered collegen, the connective tissue in the meat, that provides both the tenderness and the mositure in brisket.

The best advice I would give anyone who is cooking brisket, use a probe thermo only to watch for the stall (not the 160 degree stall the ~180 degree stall). Wait for the stall to stop then go check the meat with a probe. If it wasn't done, then wait 30-60 mins or 5 degrees the recheck. Do until tender and then pull and rest.

I ran my brisket at 245-270 this weekend, I like 250 a little better for briskets than 225.
__________________
Current Smoker: Char-Griller Kamado
Teltum is offline   Reply With Quote


Thanks from:--->
Reply

Tags
brisket, burnt ends, uds

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 12:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.