The BBQ BRETHREN FORUMS.  



Our Homepage Donation to Forum Overhead Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Amazon Affiliate
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking.


Reply
 
Thread Tools
Old 05-04-2013, 05:13 PM   #1
ChetPunisher
On the road to being a farker
 
ChetPunisher's Avatar
 
Join Date: 04-28-13
Location: Holland, Michigan
Default Chet's Whiskey Barrel Smoker

Just the beginning, but I have to start somewhere. Letting the barrel soak to expand the stakes as much as possible before screwing the stakes. I'm still trying to figure out what screws I should use and not go broke.




ChetPunisher is offline   Reply With Quote


Old 05-04-2013, 06:47 PM   #2
yakdung
is One Chatty Farker
 
Join Date: 04-12-10
Location: Houston, Texas
Default

Too cool what else can I say. Can't wait for more pictures.
yakdung is offline   Reply With Quote


Thanks from:--->
Old 05-04-2013, 07:05 PM   #3
Smoothsmoke
Babbling Farker
 
Join Date: 01-20-10
Location: Monterey, CA
Default

<----Staying tuned!
__________________
Kamado Big Joe
[COLOR=Red]Kamado Classic Joe
Kamado Joe Jr. [/COLOR]
A bunch of Webers
Smoothsmoke is offline   Reply With Quote


Thanks from:--->
Old 05-04-2013, 07:18 PM   #4
Toney Marconi
Full Fledged Farker
 
Toney Marconi's Avatar
 
Join Date: 11-26-12
Location: Richmond, VA
Default

Do you need to screw every single board on every ring? If so, that's a lotta screwing (and screws).
Toney Marconi is offline   Reply With Quote


Thanks from:--->
Old 05-04-2013, 07:20 PM   #5
ChetPunisher
On the road to being a farker
 
ChetPunisher's Avatar
 
Join Date: 04-28-13
Location: Holland, Michigan
Default

All the pictures I have seen have the bands screwed in at every stake. I just need to know which screws to use. If they are the 75&#162; ones I found I am gonna just ditch this to my wife for planting in and move on to a UDS...
ChetPunisher is offline   Reply With Quote


Old 05-04-2013, 07:25 PM   #6
Toney Marconi
Full Fledged Farker
 
Toney Marconi's Avatar
 
Join Date: 11-26-12
Location: Richmond, VA
Default

I don't blame you. That's an expensive screw. There has to be a cheaper screw you can use.
Toney Marconi is offline   Reply With Quote


Thanks from:--->
Old 05-04-2013, 07:28 PM   #7
ChetPunisher
On the road to being a farker
 
ChetPunisher's Avatar
 
Join Date: 04-28-13
Location: Holland, Michigan
Default

The one I found was a self tapping stainless steel screw for steel... Not sure if I can get away with a self tapping wood screw. I guess I should just go grab a bunch of different self tappers and give it a shot..
ChetPunisher is offline   Reply With Quote


Old 05-04-2013, 07:49 PM   #8
Oldbob
is One Chatty Farker

 
Oldbob's Avatar
 
Join Date: 08-24-06
Location: Kokomo,Indiana
Default

Here is a Link to Self Tapping screws at Lowes


http://www.lowes.com/pd_59183-37672-...%7C1&facetInfo=


Hope this helps You !!


Bob
__________________
Chargriller Akorn
Drum Smoker " Old Smokey " Work in Progress
Kingsford Premium Charcoal Grill
Weber Gasser Genesis Silver A
Pit Barrel Cooker
Maverick ET-732
VietNam Veteran US Navy
May you Sleep in Peace always...and Please....Thank a Veteran for That Privilege!!
Oldbob is offline   Reply With Quote


1 members found this post helpful.
Thanks from:--->
Old 05-04-2013, 09:27 PM   #9
realspaazz
Take a breath!
 
realspaazz's Avatar
 
Join Date: 08-21-10
Location: Lake Worth, Florida
Default

The self tappers work ok in thin soft metal, but i think that they hold poorly in wood (I feel that the drilling function drills too large of a pilot hole in the wood for the screw to hold well) I would get regular pan head screws long enough to go through the band and half to three quarters of the way through the slats (you don't want to penetrate the inside of the barrel) Get two sizes of drill bit, one the same diameter as the screw threads and the other just a bit smaller than the diameter of the shaft through the center of the screw.

Use the larger bit to drill through the metal band. On this project you will probably dull several bits so buy a few, drilling at a slow speed will help to keep the bit sharp longer. A center punched dimple on the band will help to keep the bit from "wandering". A stop collar on the bit will keep you from drilling too deep.

Use the smaller bit to drill a pilot hole into the wood. Again, a stop collar will keep the bit from drilling too deep. You want your pilot to be almost as deep as the screw will penetrate.

Oak is tough wood. A little paraffin wax on the screw threads will help them cut in easily. If you are using a power driver, set the clutch so that the screw just comes tight to the band. You can always cinch it up by hand. That will minimize snapping the screws off as you drive them. If you can find USA made screws, you will likely have less breakage. (Try Van Wieren's Hardware. (I grew up in Holland))
Hope that this helps. Good Luck! It looks like a cool project.
__________________
18.5 WSM, Green Weber Genesis320, Cast iron firepit(w/grill), and a Copper Weber 22" OTS

Last edited by realspaazz; 05-04-2013 at 09:28 PM.. Reason: Paragraph indents did not work/hard to read
realspaazz is offline   Reply With Quote


2 members found this post helpful.
Thanks from: --->
Old 05-05-2013, 07:14 AM   #10
gbaker770
Found some matches.
 
Join Date: 11-23-10
Location: Louisville, KY
Default

Try Fastenal, they are going to be much cheaper than Lowes and you can get exactly what you're looking for.
Subscribing to your build.
gbaker770 is offline   Reply With Quote


1 members found this post helpful.
Thanks from:--->
Old 05-05-2013, 07:55 AM   #11
Johnny_Crunch
Babbling Farker

 
Join Date: 04-03-10
Location: Cypress TX
Default

Cool build. Can't wait for the rest.
__________________
J Crunch
Johnny_Crunch is offline   Reply With Quote


Thanks from:--->
Old 05-05-2013, 10:07 AM   #12
J-Rod
is One Chatty Farker
 
J-Rod's Avatar
 
Join Date: 08-15-12
Location: Irish Hills, MI
Default

What realspazz said. It's a lot of drilling, but it'll pay off in the end when yer eating tasty Q. Don't shelf the build yet!

Edit- and whatever you do be sure to use an electric drill to drill all those holes! Cordless ones are fine for installing screws but they aren't adequate for repeated heavy drilling.
__________________
Okie Joe offset, UDS, Akorn, Weber Kettles, I'm JD.
J-Rod is offline   Reply With Quote


Thanks from:--->
Old 05-05-2013, 10:16 AM   #13
chicagokp
Babbling Farker

 
chicagokp's Avatar
 
Join Date: 02-17-11
Location: Chicago north 'burbs IL
Default

Very cool.
__________________
Shirley Fabrication 24x60 staightback cabinet + warmer
Battle Box
Midi UDS
Weber Performer
22.5 Weber OTG
WGA Charcoal
Weber Genesis
chicagokp is offline   Reply With Quote


Thanks from:--->
Old 05-11-2013, 10:24 AM   #14
ChetPunisher
On the road to being a farker
 
ChetPunisher's Avatar
 
Join Date: 04-28-13
Location: Holland, Michigan
Default

I'm thinking of doing an electric unit on this one.The chance of flare upas and burning the barrel down worries me. What do you all think?
ChetPunisher is offline   Reply With Quote


Old 05-11-2013, 10:41 AM   #15
Freddy j
is one Smokin' Farker
 
Join Date: 11-22-12
Location: Boston
Default

Subscribed! Very interested in this one. That is a very handsome barrel.
__________________
Kamado Joe Big Joe -- Kamado Joe Classic -- Kamado Joe Jr -- WSM mini
Freddy j is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Forum Custom Search: Enter your Search text below. GOOGLE will search ONLY the BBQ Brethren Forum.





All times are GMT -5. The time now is 11:23 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts