ブタ
The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 02-21-2013, 04:03 PM   #1
Neonnblack
Full Fledged Farker
 
Join Date: 01-15-13
Location: Reno, NV
Downloads: 0
Uploads: 0
Default Another you guessed it....UDS thread.

I realized i never posted my UDS yet, well its a drum, and it smokes meats. Aint much else to it.
When i picked the barrel up, had the damned red liner (at this time in my infancy i didnt know it was going to be bad).

During the urn out, where i was like yeah cool that red liner will be banished!(not so).


While i had the barrel burning I started on my basket. Had my makeshift brake (which is very handy, just a piece of angle clamped to a piece of steel)

And it turned out this.

Cool, i thought, im near ready to be smoking it up! Then i hit a road block, that damn red liner, never came out. So, im cheap and dont value my time very much so instead of taking it to a shop to have it sandblasted, i decided i'd flap disc it all out. It wasnt fun, VERY dirty and took about an hour or so, just grinding away. My suggestion for any new UDS guys: get an unlined drum, or an old oil drum and burn it out a few times.

So after all that i drilled my wholes, and set the top grate in and decided to revel in my confidence that i just made something badass.

Ran a couple test fires through it, as well as seasoning it. then i found out on here, my basket is way to small -_-. First rebuild.
So here was the new basket next to part of the old basket.

Obviously a massive, but needed difference.

At this point for venting all i had were holes cut in the drum and planned on using sheet magnet, it didnt work, i struggled through two cooks using those damn magnets, one fell off in one cook and it shot to like 400 degrees before i caught it. So i changed them into what i thought would be a great, cheap idea.

And once again, they sucked and fell off, didnt seal very well, etc. So another redesign sent me this way. With my makeshift brake again i came up with this (and partly from another design).
Bent the sheet up.

I also stabbed my finger with the drill.

Cut a hole in it, a cover plate and we ended up with this. Open.

Closed.

This is by far the best design ive came up with (i dont want ball valves and pipe on mine, wanted a bit of a cleaner look) and so far has been flawless.

I used it just like this for a few weeks before i decided i needed a table on it, so i got a bed frame, a piece of 3/4 oak plywood and a router from work, for the grand total of....wait for it.... 20 bucks. The router even had some US made bits with it. So i bolted up the frame after cutting and drilling the extra brackets off.

Then i got to work on the oak for the tops. I didnt picture most of this because i messed up a few cuts And i got really irritated with it and had to ghetto one side together. But i did take a picture of the routed side while i was doing that.

And then i stained it ponderosa green. No pics of this either.
Screwed the tops down and we are at this point.(just imagine it without the dome lid on it, hehe)

Now, talking about that dome lid, i was surfing CL and found a 22 inch kettle style Q for 25 bucks.

Figured i would use the top for mine and the bottom for another barrel thats being built.

This is where things got a little tricky, this q was only 22 wide, and not 22.5 like the weber. So i had to get creative with how to fit the lid. What i came up with keeps it sealed (i hope i havent used it yet with the dome lid) And makes the drippings drip in the barrel and not down the side. ( a few of these pics are the same, sorry)
Edge pounded out flat.

Still didnt have enough to remake the lip like this so i had to keep thinking of a solution. I tried making it like a cone by bending the flat lip down, which didnt work at all. then i thought well maybe i could push the lid into the barrel instead of having it sit on the barrel, so i grabbed some pliers and bent the flat lip up. and set it in.

This is what i had to work with, so i clamped the lid to the drum in two spots and started reshaping the ring. and ended up with this.

It sits nicely, and with the dip inside the barrel nothing can leak out. I still need to get the clamp ring that has a bolt on the outside to clamp and not the lever like i have now. Also, i need to rework the hinges of the dome so i can use them on the drum also.

And thats pretty much it so far, im up to this point now with the drum. Have performed successful cooks and hope to keep churning out bbq.


I still have plans for wheels, and a few other storage type things on it. One step at a time.

Thanks for looking at my build thread, folks.
Neonnblack is offline   Reply With Quote


Thanks from: --->
Unread 02-21-2013, 04:28 PM   #2
N8man
Babbling Farker
 
N8man's Avatar
 
Join Date: 05-09-07
Location: God's Country Ossipee-Osceola NC
Downloads: 0
Uploads: 0
Default

OutStanding!!! Thanx for sharing the process!!!
__________________
N8man
Average Joe Backyard Enthusiast

How I Fire Up That Ugly DrumPit Smoker!!!!
N8man is offline   Reply With Quote


Unread 02-21-2013, 04:37 PM   #3
JandJbuidasmoker
Full Fledged Farker
 
JandJbuidasmoker's Avatar
 
Join Date: 02-18-13
Location: Terre Haute, Indiana
Downloads: 0
Uploads: 0
Default

Wow...Thanks for taking the time to explain it completly! I was curious how that worked and you took care of it for me! Pretty cool! How much Q can you get in there?
JandJbuidasmoker is offline   Reply With Quote


Unread 02-21-2013, 04:39 PM   #4
Oldbob
is One Chatty Farker

 
Oldbob's Avatar
 
Join Date: 08-24-06
Location: Kokomo,Indiana
Downloads: 0
Uploads: 0
Default

Lookin Good Brother !!
__________________
Chargriller Akorn
Drum Smoker " Old Smokey " Work in Progress
Kingsford Premium Charcoal Grill
Weber Gasser Genesis Silver A
Pit Barrel Cooker
Maverick ET-732
VietNam Veteran US Navy
May you Sleep in Peace always...and Please....Thank a Veteran for That Privilege!!
Oldbob is offline   Reply With Quote


Unread 02-21-2013, 05:23 PM   #5
ITBFQ
is one Smokin' Farker
 
ITBFQ's Avatar
 
Join Date: 09-17-12
Location: Oswego, IL
Downloads: 0
Uploads: 0
Default

Looks great!
__________________
Matt - KCBS CBJ; 18.5" WSM; UDS; DigiQ DX2; CharBroil Gasser; Maverick; OTS; etc.
ITBFQ is offline   Reply With Quote


Unread 02-21-2013, 05:59 PM   #6
Neonnblack
Full Fledged Farker
 
Join Date: 01-15-13
Location: Reno, NV
Downloads: 0
Uploads: 0
Default

Thanks for the kind words, folks. Im currently putting a paint job on it!

Quote:
Originally Posted by JandJbuidasmoker View Post
Wow...Thanks for taking the time to explain it completly! I was curious how that worked and you took care of it for me! Pretty cool! How much Q can you get in there?
Alot, I can fit 30+ pounds of butt at once, about 6 racks at the same time, a large butt and 4 or so racks, a ham and a butt, you can really fit tons of stuff in these things.
Neonnblack is offline   Reply With Quote


Unread 02-21-2013, 09:04 PM   #7
Neonnblack
Full Fledged Farker
 
Join Date: 01-15-13
Location: Reno, NV
Downloads: 0
Uploads: 0
Default

Its got some color now.
Neonnblack is offline   Reply With Quote


Unread 02-22-2013, 04:36 AM   #8
fedex
Full Fledged Farker
 
fedex's Avatar
 
Join Date: 06-21-10
Location: Cypress, CA
Downloads: 0
Uploads: 0
Default

Nice Out of the Box thinking on the lid mod. The bed rails for the side table is Brilliant. Thanks for sharing.
__________________
UDS, Jumbo Joe 2013, 26" Weber, SS Blue Performer, WGA Charcoal, Q100 & Wife Model#1962
fedex is online now   Reply With Quote


Unread 02-22-2013, 10:38 AM   #9
Neonnblack
Full Fledged Farker
 
Join Date: 01-15-13
Location: Reno, NV
Downloads: 0
Uploads: 0
Default

Be for warned about bed rails. They are plentiful, and cheap, but arent fun to work with. And dont even think about using them as a structural piece to anything. Bed rails are made from whatever scrap the manuf. can get a hold of. There are very hard spots, and soft spots and everything in between. Can be incredibly hard to drill. For instance i went through 3 or 4 cobalt 1/4 bits for the 12 or so holes i drilled in this particular frame.
Neonnblack is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 08:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts