UDS Lid help

biggs98 · 01-31-2013, 04:31 PM

Any idea how to get the lid off cleanly??? Previous drums I had they took it off for me and rolled the top of the drum. Any help is always appreciated.

jrn · 01-31-2013, 04:41 PM

Carefully grind on the top of that lip. The top will fall in the drum. Use a angle grinder and a soft disc. Matter of fact somebody just posted pictures of these discs yesterday, I believe. There are several ways to do this, but this is my preferred method.

Carbon · 01-31-2013, 04:43 PM

I used an old wood chisel to cut the top. Took about 10 minutes and used an angle grinder to smooth out the edges.

4uweque · 01-31-2013, 04:44 PM

I used a jig saw with a metal cutting blade the I laid the drum on its side over a piece of carpet and took a hammer to fold the lip flat. It worked well and didn't take long.

El Ropo · 01-31-2013, 04:47 PM

3/4" cold chisel and hammer works great, and is pretty fast. Just remember to wear ear protection, it gets loud.

Use it like a can opener, slightly angle chisel so it's not punching through but cutting, and angle the chisel blade towards outside of drum to get as close a cut as possible.

Swamp Donkeyz BBQ · 01-31-2013, 05:16 PM

Air hammer with a chisel bit. Take your time and it will cut pretty clean.

funugy · 01-31-2013, 05:23 PM

I used my sawzall and cut right up against the lip, then broke the sharp edges with my angle grinder. Took about 10 min in all. It actually took me longer taking out my tools and setting up than the work did.

biggs98 · 01-31-2013, 06:44 PM

Thx fellas.... If I cut it from the top, how am I going to be able to use the lid???

Carbon · 01-31-2013, 06:48 PM

Quote:

Originally Posted by biggs98

Thx fellas.... If I cut it from the top, how am I going to be able to use the lid???

You don't, you borrow the lid from your kettle...:)))

jrn · 01-31-2013, 06:50 PM

Quote:

Originally Posted by Carbon

You don't, you borrow the lid from your kettle...:)))

Yep.

knakker123 · 01-31-2013, 06:58 PM

This is how i did it. My english is a bit rusty but i`ll try to explain. This took me a while (about 30 minutes) but had a nice result. The lid of my barrel was curved around the cilinderend of the barrel . So i used my angle grinder with a fairly rough flap disc to grind off just a mm orso (sorry idk inches) from that `curve` at the side of the barrel.(just the lid layer) The lid came off clean and a perfecly flat barrelcilindertop remained. Carefull! The lid has razor sharp edges when it comes of.

jrn · 01-31-2013, 07:42 PM

Quote:

Originally Posted by knakker123

This is how i did it. My english is a bit rusty but i`ll try to explain. This took me a while (about 30 minutes) but had a nice result. The lid of my barrel was curved around the cilinderend of the barrel . So i used my angle grinder with a fairly rough flap disc to grind off just a mm orso (sorry idk inches) from that `curve` at the side of the barrel.(just the lid layer) The lid came off clean and a perfecly flat barrelcilindertop remained. Carefull! The lid has razor sharp edges when it comes of.

Yeah I've done the same thing too. And no kidding the edge is like a razor! But it will work.

swamprb · 01-31-2013, 08:40 PM

Quote:

Originally Posted by Swamp Donkeyz BBQ

Air hammer with a chisel bit. Take your time and it will cut pretty clean.

Second this emotion!

Don't forget the soon to be patented "swamprb flange mod"!

jrn · 01-31-2013, 09:25 PM

Swamp, I've been eyeballing my kettle bottom everytime I walk past it. Especially seeing as how I've got massive amounts of grease leaking down my closed top drum. What would you suggest cutting it with? Jig saw?

swamprb · 01-31-2013, 09:27 PM

Quote:

Originally Posted by jrn

Swamp, I've been eyeballing my kettle bottom everytime I walk past it. Especially seeing as how I've got massive amounts of greasing leaking down my closed top drum. What would you suggest cutting it with? Jig saw?

Rotary cut off wheel!

01-31-2013, 04:31 PM	#1
biggs98 Full Fledged Farker Join Date: 08-27-08 Location: West Sayville NY Downloads: 0 Uploads: 0	UDS Lid help Any idea how to get the lid off cleanly??? Previous drums I had they took it off for me and rolled the top of the drum. Any help is always appreciated. __________________ Joe - CHUBBY HUBBY BBQ / STAINLESS UDS(Build in Progress)/2 UDS /1 WSM / Weber Gasser/ 22.5 Weber Kettle/ The Absolute Fastest Super Fast *BLACK* Thermapen

01-31-2013, 04:41 PM	#2
jrn Full Fledged Farker Join Date: 07-30-12 Location: Quitman, Ms Downloads: 0 Uploads: 0	Carefully grind on the top of that lip. The top will fall in the drum. Use a angle grinder and a soft disc. Matter of fact somebody just posted pictures of these discs yesterday, I believe. There are several ways to do this, but this is my preferred method. __________________ UDS, mini wsm

01-31-2013, 04:43 PM	#3
Carbon is One Chatty Farker Join Date: 08-24-08 Location: Los Angeles Downloads: 0 Uploads: 0	I used an old wood chisel to cut the top. Took about 10 minutes and used an angle grinder to smooth out the edges. __________________ ....UDS....Mini-WSM....Midi-WSM....Mod-ECB....22.5-OTG....34"wood fired pizza oven....

01-31-2013, 04:44 PM	#4
4uweque Full Fledged Farker Join Date: 02-16-12 Location: Memphis Tenn. Downloads: 0 Uploads: 0	I used a jig saw with a metal cutting blade the I laid the drum on its side over a piece of carpet and took a hammer to fold the lip flat. It worked well and didn't take long. __________________ 3 UDS's / Orion cooker / gas cabinet converted to charcoal / Weber kettle / Cowboy grill

01-31-2013, 04:47 PM	#5
El Ropo Babbling Farker Join Date: 10-06-10 Location: Austin, TX Downloads: 1 Uploads: 0	3/4" cold chisel and hammer works great, and is pretty fast. Just remember to wear ear protection, it gets loud. Use it like a can opener, slightly angle chisel so it's not punching through but cutting, and angle the chisel blade towards outside of drum to get as close a cut as possible. __________________ Modded Brinkmann Gourmet. Basic UDS. Rescued 22.5" OTS. Weber SJS. Stubbs. B&B Oak Lump. Cannondale 2009 F8 (for burning off all the great BBQ)

01-31-2013, 05:16 PM	#6
Swamp Donkeyz BBQ is one Smokin' Farker Join Date: 07-25-12 Location: Huntsville, Tx Downloads: 0 Uploads: 0	Air hammer with a chisel bit. Take your time and it will cut pretty clean.

01-31-2013, 05:23 PM	#7
funugy On the road to being a farker Join Date: 05-21-12 Location: Oak Harbor, WA Downloads: 0 Uploads: 0	I used my sawzall and cut right up against the lip, then broke the sharp edges with my angle grinder. Took about 10 min in all. It actually took me longer taking out my tools and setting up than the work did.

01-31-2013, 06:44 PM	#8
biggs98 Full Fledged Farker Join Date: 08-27-08 Location: West Sayville NY Downloads: 0 Uploads: 0	Thx fellas.... If I cut it from the top, how am I going to be able to use the lid??? __________________ Joe - CHUBBY HUBBY BBQ / STAINLESS UDS(Build in Progress)/2 UDS /1 WSM / Weber Gasser/ 22.5 Weber Kettle/ The Absolute Fastest Super Fast *BLACK* Thermapen

01-31-2013, 06:58 PM	#11
knakker123 Found some matches. Join Date: 01-12-12 Location: Europe Holland Downloads: 0 Uploads: 0	This is how i did it. My english is a bit rusty but i`ll try to explain. This took me a while (about 30 minutes) but had a nice result. The lid of my barrel was curved around the cilinderend of the barrel . So i used my angle grinder with a fairly rough flap disc to grind off just a mm orso (sorry idk inches) from that `curve` at the side of the barrel.(just the lid layer) The lid came off clean and a perfecly flat barrelcilindertop remained. Carefull! The lid has razor sharp edges when it comes of.

01-31-2013, 09:25 PM	#14
jrn Full Fledged Farker Join Date: 07-30-12 Location: Quitman, Ms Downloads: 0 Uploads: 0	Swamp, I've been eyeballing my kettle bottom everytime I walk past it. Especially seeing as how I've got massive amounts of grease leaking down my closed top drum. What would you suggest cutting it with? Jig saw? __________________ UDS, mini wsm