The BBQ BRETHREN FORUMS.


Forum Portal Recipes Smoke Signals Magazine Welocme Merchandise Associations Purchase Subscription Brethren Banners
Go Back   The BBQ BRETHREN FORUMS. > Discussion Area > Q-talk

Notices

Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, Equipment and just outdoor cookin' in general, hints, tips, tricks & techniques, success, failures... but stay on topic. And watch for that hijacking.


Reply
Thread Tools
Unread 11-11-2012, 10:34 PM   #1
DougMorford
Found some matches.
 
Join Date: 02-03-12
Location: Moscow, ID
Downloads: 0
Uploads: 0
Default DIY Water Stuffer

Hey everyone, I thought I'd share the sausage stuffer I made yesterday. It's made from 3" pvc, some reducers and increasers, and a garden hose to NPT thread adapter.

Instead of having two holes for water inflow and outflow, I'm just using a gated Y with an inline ballvalve in front of that. This works pretty well, but i need to thread a hole in the water chamber to purge the air so that I don't have to put the stuffer on its end to fill it with water.

I wandered all over the hardware store looking for something that might work as a plunger. What I found is designed to temporarily plug an open pipe end. It works by screwing down on the red knob, forcing the rubber ring to expand. I had to cut off the shoulder which would normally keep it from fitting inside the pipe. It was important to only shave down this shoulder enough so that it would fit in the pipe, because it acts as a guide to keep the plunger from turning sideways. I like this plunger because it's very easy to slide into the pipe, and you just tighten it up to create a good fit. I haven't had any problems with water getting into my meat.

Three things I would have done differently:

-use threaded caps instead of increasers and reducers. I would have had to drill some threaded holes, but as it is now there are a lot of nooks and crannies to clean because of all the adapters.

-It would have been just as easy to do this with 4" pvc. I had to load this four times to stuff 15 lbs of meat, and it would be MUCH easier to load a four inch pipe. My hand just barely fit in the three inch pipe, and my forearm wasn't even close to fitting.

-US Plastics.com sells clear pcv. It would be great to see what's going on inside the stuffer.





The Plunger:






Last edited by DougMorford; 11-11-2012 at 10:44 PM.. Reason: Pictures
DougMorford is offline   Reply With Quote


Thanks from: --->
Unread 11-12-2012, 08:42 AM   #2
cowgirl
somebody shut me the fark up.

 
cowgirl's Avatar
 
Join Date: 07-18-07
Location: Oklahoma
Downloads: 0
Uploads: 0
Default

Great job!!


I love pvc.
__________________
jeanie
sittin' by the campfire with my Brethren friends.
Lifetime member of the Society for the Preservation of Authentic Royal Magical Rare Kaskaskian Peppers (Thanks Ash :))

http://cowgirlscountry.blogspot.com/
cowgirl is online now   Reply With Quote


Unread 11-12-2012, 08:59 AM   #3
hamiltont
is One Chatty Farker
 
hamiltont's Avatar
 
Join Date: 05-24-10
Location: Kearney, NE
Downloads: 0
Uploads: 0
Default

Genius!!!
__________________
If Homebrew & BBQ aren't the answer, then you're askin' the wrong questions... Cheers!!!
hamiltont is offline   Reply With Quote


Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Loading



All times are GMT -5. The time now is 01:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.
no new posts