|
Q-talk *ON TOPIC ONLY* QUALITY ON TOPIC discussion of Backyard BBQ, grilling, equipment and outdoor cookin' . ** Other cooking techniques are welcomed for when your cookin' in the kitchen. Post your hints, tips, tricks & techniques, success, failures, but stay on topic and watch for that hijacking. |
|
Thread Tools |
10-04-2011, 02:59 AM | #1 |
Got Wood.
Join Date: 09-20-11
Location: Belgium - Limburg
|
DIY PID Controller
Hi everybody,
Smoke in NJ asked me how i built my PID controller and instead of replying in PM i thought I'd share it with all you guys ;) It all started when i made my third PP...I got tired with staying all night long by my Q, just to keep sure it stayed at a stable temperature... I looked everywhere for a system, but all of them were more expensive than i could afford... So i started with a budget of 50€ (about 66$) and went out on the Internet and found the most expensive parts i needed... I bought two fans which cost about 5$ for the two of them... The PID controller was about 10$...you can find them cheaper if you shop around. I bought the 12/24V one --> D1S-2R-24, but a better choice would have been the D1S-VR-24 because of the SSR relay. The other small parts (switches, connectors, jacks, box, ...) i bought in a local electronics store... All together i went 6$ above my initial budget... Here is the schematic for connecting all the parts... And for those of you that like Pr0n... The internal parts... The outside of the box... Here i mounted the fan to the door of the Q... For those of you that would like to see the PID in action... MOV_0143.mp4 video by BillieChillie - Photobucket@@AMEPARAM@@http://vid893.photobucket.com/player.swf?file=http://vid893.photobucket.com/albums/ac134/BillieChillie/MOV_0143.mp4@@AMEPARAM@@vid893@@AMEPARAM@@893@@AME PARAM@@ac134/BillieChillie/MOV_0143@@AMEPARAM@@mp4 and MOV_0144.mp4 video by BillieChillie - Photobucket@@AMEPARAM@@http://vid893.photobucket.com/player.swf?file=http://vid893.photobucket.com/albums/ac134/BillieChillie/MOV_0144.mp4@@AMEPARAM@@vid893@@AMEPARAM@@893@@AME PARAM@@ac134/BillieChillie/MOV_0144@@AMEPARAM@@mp4 the PID is in Autolearn mode. Hope you enjoyed this read ;) Greetings Tom
__________________
OTP 22.5". Mini Smoker. 16" Cheapo Offset smoker. 22'' Selfmade TDS. DIY PID Controller |
|
Thanks from: ---> |
10-04-2011, 05:08 AM | #2 |
Full Fledged Farker
Join Date: 06-25-10
Location: Leicester UK
|
Excellent stuff!
__________________
Miss Piggy's BBQ. U.K. European Champions. Jack Daniel's 2012 Top International Team. |
|
10-04-2011, 06:08 AM | #3 |
is Blowin Smoke!
Join Date: 05-09-11
Location: Granite City, Illinois (Near St. Louis "GO CARDS")
|
Wow! It's like your talking French. I did understand any of it, but I looks great. Good job.
__________________
22.5 WSM, 120 Gallon Offset, Weber Performer, IQ-110, ET-732 |
|
10-04-2011, 06:24 AM | #4 |
somebody shut me the fark up.
Join Date: 07-30-11
Location: Pemberton, New Jersey
|
Whats the value of the resistor between points A and B? and what wattage (1/2 or 1)?
|
|
10-04-2011, 06:29 AM | #5 |
Found some matches.
Join Date: 09-25-11
Location: Hoboken, NJ
|
Thanks so much. This is something I want to try; once I get up the courage.
The pid controller costs less than what I've seen around. More googling for me.
__________________
Northern NJ * Weber Performer 22.5"; WSM 22.5" |
|
10-04-2011, 06:50 AM | #6 |
Full Fledged Farker
Join Date: 07-28-09
Location: Melbourne, Florida
|
I applaud homebrewing a controller. I made my own a couple of years ago and have been tweaking at it ever since.
My problem with using a controller such as you've decided on is that the fan is either 100% on or 100% off. When the fan is fully on it will blow a huge amount of air into the cooker until it reaches the target temperature. The problem is that after the fan turns off the temperature will continue to climb. The temperature swings will be very wide. I found that turning the fan on by varying degrees worked best. There's a huge discussion going on over on the Virtual Weber Bullet board about this very thing. Some of those guys have gone WAY overboard with all sorts of software stuff that this hardware engineer doesn't understand. http://tvwbb.com/eve/forums/a/tpc/f/...03/m/909108292 Russ
__________________
Lead Cook 'Second Star BBQ' using a Big Orange 'Prince', 22 OTG, SJS FBA & KCBS CBJ |
|
Thanks from:---> |
10-04-2011, 09:52 AM | #7 | |||
Got Wood.
Join Date: 09-20-11
Location: Belgium - Limburg
|
Quote:
Quote:
Quote:
First of all thanks for the nice comment :) Actually that's what a PID does...It calculates the time it takes to get to a certain temperature. The first time it will overshoot, the next time a little bit less and the third time it will stay at the set temperature. When the PID notices that the temperature is dropping it will activate for a few seconds. If you like the theory behind a PID see the wiki. ;) I got mine tweaked (autolearn modus of the unit) to 0.2°C (0.36°F correct me if i'm wrong) offset... Which means that if i set my temperature to 230°F (110°C) it doesn't go above 230.36°F (110,2°C) and below 229.64°F (109,8°C) Which is just fine by me ;) Oh and in the schematic there's a potentiometer in the circuit of the fan. So i could change the speed of the fan if necessary. The only thing is i think 100ohm isn't enough, because that one burned out on the first try. So mine is built with the potentiometer, but it isn't connected any more... Greetings
__________________
OTP 22.5". Mini Smoker. 16" Cheapo Offset smoker. 22'' Selfmade TDS. DIY PID Controller |
|||
|
02-28-2012, 02:09 PM | #8 | |
is One Chatty Farker
Join Date: 03-29-11
Location: Beijing,China
|
You have 2 options
Quote:
2.You need a better thermostat with PID output. variable voltage output is even better than SSR output. |
|
|
Thanks from: ---> |
02-28-2012, 03:15 PM | #9 | |
is one Smokin' Farker
Join Date: 09-13-11
Location: Fort Smith, Ar.
|
Quote:
Nice you didn't have to say anything as what he is doing could take business away from you but instead like a true bretheren you lended your advice.. Nice job and in the sprit of the bretheren...
__________________
[SIZE=2][B]Jim Boston[/B][/SIZE] [B][COLOR=black]Current Smoker[/COLOR][/B] [COLOR=red]"The most reliable, easiest to make at home, Smoker [B]"The UDS"[/B] W/ an Auber temp. Controller w/ 20CFM Blower.[/COLOR] [FONT=Arial][B]Future Smoker [/B][/FONT] [FONT=Arial]$5438.25 Total BYC Smoker!![/FONT] [SIZE=2]Some people spend an entire lifetime wondering if they made a difference in the world. But, the Marines don't have that problem. [/SIZE] [SIZE=1]Ronald Reagan, President of the United States; 1985 [/SIZE] |
|
|
Thanks from: ---> |
02-29-2012, 11:37 AM | #10 |
Full Fledged Farker
Join Date: 10-25-09
Location: Hazzard County, MD
|
Can also put a simple damper on the fan
|
|
02-29-2012, 12:02 PM | #11 |
is one Smokin' Farker
Join Date: 06-09-10
Location: Oak Forest, IL
|
Where did you get the fans from?
__________________
Co-Pitmaster of Hatfield and McCoy Barbecue Pitmaster of South Side Pit Men UDS's, Multiple Weber Grills |
|
02-29-2012, 02:24 PM | #12 |
is one Smokin' Farker
Join Date: 12-14-10
Location: Orangevale California
|
Very cool Billie. I am about as dumb as you can be when it comes to electronics, however my FIL can talk to another country with a tin can, 2' of rope and a coat hanger.
Luckily for me, he has siad that he would help me build 1 or 3 of these. Would it be possible for you to list the parts, including the misc. and whatnots. He is in Arkansas right now but coming home in a few weeks and I would love to have all the parts when he got here so I can put him stright to work. Just like he always does to me
__________________
[CENTER]Chad [/CENTER] [CENTER]Gator Pit (Holy Smokees)[/CENTER] [CENTER]Custom built Propane Offset Smoker[/CENTER] [CENTER]Rescued Red MasterTouch - 1998[/CENTER] [CENTER]Smoky Joe - 1984 (My Little Girls)[/CENTER] [CENTER]Ranch Kettle X2- 2008 With Brother Marty Leach's Handles and 1991 CL find.[/CENTER] [CENTER]SS Weber Performer X 2 [/CENTER] |
|
02-29-2012, 05:28 PM | #13 |
Knows what a fatty is.
Join Date: 09-17-10
Location: Memphis, Tn
|
Please please post the links to where you bought the cheap fan and PID! I've been looking for an affordable 12 volt PID for what seems like forever!! Thanks Brother!
|
|
Thanks from: ---> |
04-04-2012, 09:41 PM | #14 |
Knows what a fatty is.
Join Date: 03-29-12
Location: Dallas, TX
|
Perhaps a day late and a dollar short, but I have questions about this design.
I have found the Sestos D1S-VR-24 on eBay, and I am wondering if you can connect the 12V directly to the 12V SSR output or will that blow the controller? I've seen other PIDs with SSR control that require a separate SSR. Thanks |
|
04-05-2012, 06:20 AM | #15 |
Full Fledged Farker
Join Date: 09-25-11
Location: Follansbee, Wv
|
If the PID has a built in SSR, you will have to run the 12vdc fan power through the SSR output relay contacts. If, however, your PID has SSR control you will have to use a separate SSR. The controller I built has SSR control, so I had to use an external SSR. My build thread is here. I have a diagram in pdf format somewhere. I'll try to find it after work.
__________________
El Cheapo Royal Oak charcoal grill (heavily modified and repaired), Chargriller Pro, Webber 22.5" Silver, Webber Smokey Joe, Hibachi, UDS, ECB Square My name is Monty, dad, or grandpa...depending on who you are. |
|
|
|