bass7858
Well-known member
thanks!!
thanks olewarthog! anybody else?This is what I used. Found it in the auto section at Walmart.
Ugly Drum Smoker
- Thread starter jgh1204
- Start date
1
10_Bears
Guest
Anyone have any problems painting their drums with high temp paint in cold temperatures/weather??? I know painting should be done in a warm environment, but I'm ready to paint and winter has just kicked in here, its averaging around 15 degrees Celcius (59f).
tmhdgpth
MemberGot rid of the matchlight.
As long as the temp. is 45f and rising - not falling - you should be fine.
Skidder
Babbling Farker
This is what I used. Found it in the auto section at Walmart.
You might wanna read the product warning on the back.
N8man
Babbling Farker
Just a few friendly thoughts....
When getting a silicone gasket, be sure it is
for food service applications....
woodstove rope gasket...
that chit is fiberglass and loose fibers will flake off
and land on surfaces.....like food.....
Just some things to consider...
When getting a silicone gasket, be sure it is
for food service applications....
woodstove rope gasket...
that chit is fiberglass and loose fibers will flake off
and land on surfaces.....like food.....
Just some things to consider...
K
KGNickl
Guest
I agree with this. I'm super paranoid with fire rope because of the fiberglass, silicone because of fumes and who knows what, galvanized coated stuff, zinc coated stuff, etc.... So I used a food grade silicone to seal up my UDS lid. I rarely go above 300+ so any of the food rated silicone should be more than sufficient.
http://www.mcmaster.com/#caulk/=hz4mcs (then click "Silicone Adhesives/Sealants" and you will find them on that page)
RTV 103 is black and good for up to 400 degrees.
RTV 106 is red and good for up to 500 degrees.
I avoided automotive grade because I've heard something about formaldehyde at certain temps. But even then the RTV103 and 106 you get more for about the same price as the automotive grade stuff and shipping for me was pretty cheap. I think I had it 1-2 days after I phoned in the order.
olewarthog
Full Fledged Farker
Not sure what it says on the back but the product info on the permatex website states that it is certified to NSF/ANSI Standard 51
"This Standard is applicable to the materials and finishes used in the manufacture of food equipment (e.g., beverage dispenser, cutting board, coffee machines, domestic appliances).
The Standard is also applicable to components such as tubing, sealants, gaskets, valves, and other items intended for various food equipment applications."
BuckHunter83
Well-known member
Is $50 for a stainless steel 55 gallon drum a good deal? The guy says this barrel has only ever held potable water. Will there be a liner inside? I would be making a UDS with it. I currently have another UDS that I made but would like to make another one with a few changes...
P
Paul Worth
Guest
Get it immediately before they change their mind!
enasnidx
Full Fledged Farker
Liner or not, if that really is stainless, for $50, you snatch that up right away! It's probably worth $50 in recycling, but then again, it would make one sweet UDS!
BuckHunter83
Well-known member
Well I missed out on the stainless drum! :sad: I guess it wasn't meant to be. It's probably for the best because we are in the middle of moving and the last thing I need is another project...
pwa
is Blowin Smoke!
We've gone over this before in this thread..... as olewarthog said... as I have said... according to permatex it is certified to NSF/ANSI Standard 51 as long as you use it as a gasket under 500F your completely safe!!!
coachmccoy543
Knows what a fatty is.
Newbie here to the website. I have almost read thru this entire thread and I must say it is very informative to say the least. I have a closed head drum, no liner. Purchased the Uniflame kettle from Wal Mart for the lid and grill grate (1). To my disappointment the lid doesn't fit. Not sure if I can "persuade" it to fit or not as is. I seen somewhere among the many pages of people removing the closed lid by grinding off the top edge/ring of the barrel, just cutting thru the first layer of material.
1. Does anyone have the link to that discussion? It had a pretty good diagram about it. But I can't seem to locate it.
2. If I do remove the lid using this method does it have any effects on the structural integrity of the barrel.
3. If anyone has used this type of lid did they have any luck/tips on making it fit the barrel?
Thanks to everyone for all thier invaluable input.
1. Does anyone have the link to that discussion? It had a pretty good diagram about it. But I can't seem to locate it.
2. If I do remove the lid using this method does it have any effects on the structural integrity of the barrel.
3. If anyone has used this type of lid did they have any luck/tips on making it fit the barrel?
Thanks to everyone for all thier invaluable input.
Bludawg
somebody shut me the fark up.
JM2C but the roll crimp adds allot of structural integrity to the top of the drum.
An easy way to remove the top is to use a cold chisel and a hammer cutting around the inside like a can opener following the profile . To get the lid to fit cut the bowl from the grill about 2- 2.5" below it's li[ and bolt it into the top of the drum giving yo a perfect seal.
An easy way to remove the top is to use a cold chisel and a hammer cutting around the inside like a can opener following the profile . To get the lid to fit cut the bowl from the grill about 2- 2.5" below it's li[ and bolt it into the top of the drum giving yo a perfect seal.
BGBarracus
Knows what a fatty is.
I had a gap between my drum and my weber extension ring for the rotisserie setup. I found a Big Green Egg replacement gasket which run about $20. It's a sticky back gasket that I just ran around the ring and it filled the gap perfectly.
C
CDNQue
Guest
dddouglas
Knows what a fatty is.
Unless that drum is made of brass it has a liner. What kind I am not sure. You might scratch it to get a handle on its durablity. What size is the drum?
C
CDNQue
Guest
Thank you for the reply!
The size is 210L (55 gallons). It's 35"x23"
J.
The size is 210L (55 gallons). It's 35"x23"
J.
