View Single Post
Old 10-22-2012, 06:33 PM   #2
Toronto
Full Fledged Farker
 
Join Date: 09-12-12
Location: Toronto
Default

Unofficial Instruction Manual for Golden-Dog

There are two displays and they are labelled PV / SV. The current temperature is the top display(PV) and the lower one(SV) is used for setting your desired temperature.

The LED Display.

RUN: This green colored LED will blink very rapidly when the fan is in the OFF setting and blink slowly when the fan is in the ON setting. In the OFF setting you will see ---- in the SV display.

Hi: This red colored LED is the high temperature alarm light.

Lo: This red colored LED is the low temperature alarm light.

The controls are located below the LED display and they consist of four buttons:


This button has three menu's:

Menu #1 - activated by a single click.
Menu #2
- activated by pressing and holding the button down.
Menu #3 - activated by continuing to hold the button down while it is in Menu #2.

Menu #1
(Single Click): This will cycle you through the 4 stage temperature setting. Each button click will move you through the menu starting at SC1 and ending at AH4.

SC1 SC2 SC3 SC4
RC1 RC2 RC3 RC4
AL1 AL2 AL3 AL4
AH1 AH2 AH3 AH4

Legend:
SC= Desired pit temperature.
RC= Timing at desired pit temperature.
AL= Low temperature alarm, to turn this off set it at a temperature that will never be reached; example 0001.
AH= High temperature alarm, to turn this off set it at a temperature that will never be reached; example 0600.
1-4= This number represents the stage that it is in.

If you want only one temperature stage, simply set SC2 to 0000, it will now ignore the remaining stages.

Menu #2 (Press and Hold): This will bring you to the second menu, a single click will cycle through the menu and pressing and holding the button will bring you out of the menu.

F – C (default SV value 0000 set to Celsius): Changing the value to 0001 sets it to Fahrenheit.
SL1 (default SV value 1111): Internal parameter to define mode of alarm. For BBQ use, leave at default value.
SL2 (default SV value 1011): Internal parameter to define mode of alarm. For BBQ use, leave at default value.
HdC (default SV value 0100): Fan speed > 0001=slowest setting > 0100=fastest setting

Menu #3 (Continuing to hold the button while in Menu #2): This will bring you to the third menu, a single click will cycle through the menu and pressing and holding the button will bring you out of the menu.

P (default SV value 0030)= PID setting. Google PID controllers for a long winded explanation.
I (default SV value 0240)= PID setting. Google PID controllers for a long winded explanation.
D (default SV value 0060)= PID setting. Google PID controllers for a long winded explanation.
*AR (default SV value 0100)= use default, not sure what this does.
*r (default SV value 0000)= use default, not sure what this does.

Pb (default SV value 0000)= used to calibrate the temperature probe.
UdC (default SV value 0000)= this value must be changed when using the larger 50CFM fan. I am not certain of the value needed for the 50CFM fan.
*LCY (default SV value 0000)= use default, not sure what this does.

This button scrolls left with every click, it is used to easily enter large numbers without having to do it sequentially. This button will also start and stop the fan.

This is used to lower the current number on the SV display.

This is used to raise the current number on the SV display.


*indicates functions I do not understand.

Last edited by Toronto; 10-22-2012 at 11:41 PM..
Toronto is offline   Reply With Quote