-   Q-talk (
-   -   Ideas on Mounting Maverick ET-732 to UDS? (

ATXBen 01-02-2014 05:54 PM

Ideas on Mounting Maverick ET-732 to UDS?
Hello! This site has been a great source of information and ideas. So far I've found everything I could ever want to know without having to ask. However, my searching of the forums has left me dry on this question.

What methods have you guys used for mounting the Maverick transmitter to the UDS? Looking for ideas/solutions you guys have found to work well.

My first smoke with the unit was great, but it was just hanging off the side of the smoker by the probe wires and I don't want to do it again. I have a nice port in the wall of the UDS about 1 inch above the cooking grate that I pass the probe wires through.


ClintHTX 01-02-2014 06:11 PM

All I did was build a table for mine. Super easy. Got some l brackets from Home Depot and attached it. Now I can sit my maverick along with beers and whatever else on it.

ButtBurner 01-02-2014 06:48 PM

I have seen guys use a magnetic tool shelf from Harbor Freight or Lowes, etc

sliding_billy 01-02-2014 06:54 PM

Get the 6' wires and then you can position it away from the pit if you need to.

unixadm 01-02-2014 07:00 PM

I use the magnetic trays on my WSM and Yoder 1500. Worst case, you can remove the magnets and screw the tray onto the drum. Works great.

SmittyJonz 01-02-2014 07:09 PM

Magnetic shelf from Harbor Freight but it was 12 long and didn't sit well on curved drum so I cut it in half and bent it a little and now I got 2.

Pitmaster T 01-02-2014 08:17 PM

First, you will need to buy a PBC. It will go inside the UDS. THEN DRILL through the UDS to get to the PBC... PLACE THE probe in the hole. Voila!

okiej 01-02-2014 08:41 PM

The magnetic trays are a cool idea as is the 6 ft probes for easier placement. When there is weather while cooking it presents a new issue. A plastic box to put the transmitter in with holes for the wires combined with one of the previous suggestions would work I suppose.... Watching for better ideas as I have had the same question on drizzly days while using my offset

SmittyJonz 01-02-2014 11:34 PM

Ziplock bag.

ebijack 01-03-2014 05:58 AM

Did you look thru these photos?

ajstrider 01-03-2014 08:24 AM

Hard to beat a magnetic tool holder, it can be used for other stuff when not grilling too since it is not a permanent mount.

el_matt 01-03-2014 11:55 AM

I recently got the frame from a 2 - burner gasser, from my neighbor. With very minor tweaking, I was able to mount my UDS in it. Now I have two shelves to set whatever I want.


SmittyJonz 01-03-2014 02:24 PM

Just do it like SmokerKing did.......

MaximumJEFF 01-03-2014 04:04 PM

I just hang mine off the side with the little wire bracket it comes with

ATXBen 01-06-2014 11:12 AM

Thanks for all the ideas! I'm liking the idea of 6' probes and some sort of table/shelf for the most flexible solution.


Originally Posted by ebijack (Post 2751994)

I had not, thanks for the link! Lots of great ideas...


Originally Posted by MaximumJEFF (Post 2752448)
I just hang mine off the side with the little wire bracket it comes with

Yeah, I'm going to try this first. I didn't realize it came with that bracket as the unit I was using was actually borrowed. Mine just came in the mail.


Originally Posted by SmittyJonz (Post 2752351)
Just do it like SmokerKing did.......


All times are GMT -5. The time now is 02:47 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
2003 -2012 BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.