-   Q-talk (
-   -   Sealing the Lid on a UDS (

kwas68 03-23-2013 12:03 PM

Sealing the Lid on a UDS
Fellow Drumheads,
I see a lot of guys sealing the lids to their UDS's to make an airtight seal. I'm not sure why this is important. Why does it matter if the air leaks through small gaps rather than the large holes that you've drilled in the lid? This applies to those of us using Weber lids as well. The gaps are above (although slightly) above the cooking grate and far away from the combustion area. So what's the difference if the exhaust comes out the side or through the exhaust?

The only benefit I see is that the air-tight seal helps distinguish the fire after the cook is through.

Carbon 03-23-2013 12:09 PM

My lid is not air tight and my coals snuff out completely when I close the vents. As you say otherwise, I don't think it makes a difference.

HeSmellsLikeSmoke 03-23-2013 12:18 PM

If it is not excessive leakage it won't make much difference to the cooking; however, it may make a big difference to dripping on the outside of the drum.

4uweque 03-23-2013 01:33 PM

Mine doesn't seal great, works fine.

retired trucker 03-23-2013 03:02 PM

The only problem I can see is the ability to keep your temps constant or at a desired temperature.

ssbbqguy 03-23-2013 07:30 PM

I make sure all my lids seal for two reasons, one to keep moisture from dripping on the powdwer coating and two, Snail a man that's has used these for awhile used to run his lid being propped open for temp regulation. He had no other intake. If you think it won't add air to the fire, try it. Steve.

Chief_USN 03-23-2013 08:26 PM

I haven't cooked on mine yet, but from what I have read is it does help with temp control. I did mine mainly for aesthetics. I think it looks better cooking when all the smoke is coming out of the exhaust and not the lid. JMHO though.


AustinKnight 03-24-2013 12:29 AM

Re: Sealing the Lid on a UDS
Fire management helps temp control and snuffin it out, after a lot of cooks you wont have any leaks.

Sent from my SGH-T999

Murray in N.Z. 03-24-2013 12:57 AM

I aint got any seal on mine apart from a good ol layer of creosote/tar/smoke/liquid rundown whatever it is buildup. Works real good and dies off as soon as shut the air vent. Mind you mine is a real ugly UDS with no paint or nothing so the rundown actually stops it rusting a bit But the Weber lid fits perfect coz I took out a wedge from the drumtop and welded it up real good. I reckon thats the secret, Well actually welded it pretty darned rough and spent some time with a grinder re doing it and making it look good to tell the truth. 1st welding attempt!


kwas68 03-24-2013 11:38 AM

Assuming the leaks are much smaller than an exhaust hole, how does it affect temperature management?

For a drum lid, the gap is at the same height as the exhaust hole. I don't think the exhaust cares if it comes out of a hole you drilled or a small gap between the lid and the drum.

For either, I can't see a small gap doing much of anything because the pressure is greater inside the drum pushing the hot air out - not letting cold air. If the gap was located lower than the cooking grate height, it might be different.

JMSetzler 03-24-2013 11:42 AM

Mine leaks a bit around the edges with the Weber lid and I don't worry about it. The fire is far enough below that point that those air leaks don't play much of a role in snuffing out the fire. When I close the air intake vents the fire snuffs out rather quickly.

All times are GMT -5. The time now is 11:30 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
2003 -2012 BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.