Universal Thermostat for Sous Vide, Electric Smoker, Charcoal Smoker
#1. Up to 8 Temperature Phases.
#2. True heavy duty, long time sustained maximum current 15A
#3. Big aluminium chassis for heat radiation
#4. Timing count down or accumulated
#5. Slow Temperature rising alarm from one phase to next phase
#6. Neighbor friendly Alarm ON/OFF button
#7. Self Tuning parameters of P,I,D.
#8. Plug and play. Cord and Sensor are included
#9. 110/240 VAC fan is available for charcoal burning smoker
#1.Electrical Smoker by controlling heating element
#2. Charcoal burning smoker by controlling a 110/240 VAC fan
#3. Sous Vide used with an rice cooker
#5 proofing dough,
#6.control the temperature of a table top toaster oven,
#7 converting a freezer to a low temperature incubator for beer formation or sour dough yeast storage.
Input voltage: 80 to 260 VAC 50 /60 Hz
Output voltage: Same as the input voltage SSR.
Maximum Current: 15A for long working time
Control Action: Heating or cooling
Control Mode PID, PI, PD P or On/off
Self Tuning: Self determine parameters of P,I,D.
Sensor type: Three conductors Pt100 RTD sensor
Sensor tip dimensions: 8 mm diameter x 150 mm long.
Sensor cable length, 6 ft (2 meters)
Alarm: High /Low Temperature
Alarm ON/Off button Neighbour Friendly
Temperature accuracy: 1°C (1°F)
Temp.Phase: 1 to 8 phases up to your programming
Timing: Count Down, or Accumulated
Temp. Rising Alarm If too long from one phase to rise to next
phase, it will alarm
Dimension: 9.5x8.8x3.8 inch (245 x220x95 mm)
Testimonial from UK buyer
From: "XXX McKernan" <XXX@mckernan.info>Add sender to Contacts
To: "'ZhaoHui Wang'" <firstname.lastname@example.org>
Message contains attachments1 File (163KB)
I am having excellent results with your PID Thermostat Temperature Controller.
See picture enclosed using a conventional slow cooker as a sous-vide.
I have a question: is it possible to program Phase 1 to achieve a target temperature at which temperature it will auto-switch to Phase 2.
In this way I could guarantee that the cooking in Phase 2 at the set temperature would continue for the set time, regardless of how long it took to achieve that temperature in Phase 1.
The reason is that the slow cooker takes a long time to reach temperature.
Your device is very good but this would make it even better.
Comments by the developer and seller, the woodpelletsmoker:
There is NO such problem mentioned above, please do not worry.
The thermostat counts time AFTER it reaches to target temperature.
You can program PHASE I at 70C for 1 Minute. The slower cooker may take 30 minutes to reach to 70C. the thermostat will keep this 70C for 1 minute and then turn to PHASE II. This way the real time of PHASE I is 31 minutes.
|All times are GMT -5. The time now is 02:46 PM.|
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.