The BBQ BRETHREN FORUMS.

The BBQ BRETHREN FORUMS. (http://www.bbq-brethren.com/forum/index.php)
-   Q-talk (http://www.bbq-brethren.com/forum/forumdisplay.php?f=5)
-   -   Master Forge Double door LP smoker.. (http://www.bbq-brethren.com/forum/showthread.php?t=130059)

GARNAAL 04-07-2012 11:37 AM

Master Forge Double door LP smoker..
 
Well - I have been using this smoker for a good year now..

https://public.bay.livefilestore.com...06r.JPG?psid=1

and have to say I like it!!
it's great to regulate the temp and smoke density compared to that old side by side stick smoker I had for years - always a hassle and having to stay with it..

but still I was not quite happy with the results I got...
the leaking doors on the Master Forge always bothered me, so I looked around here for some advice ... and have to say I found a solution here that worked..

I ordered the following from Amazon for about $14..

1 "Rutland Inc Gasket Kit Tape 7'X5/8" 95-6"
1 "Permatex F81160 Hi-Temp Red RTV Silicone- 3-Ounce"

cut the Gasket tape (a Graphite Fiber Glass strip) to size for the top door..
cleaned and degreased the outer edge of the top door and placed a bead of the Hi-Temp silicone on it and lightly pressed in the Gasket tape. Let it dry with the door open.
Now I have a good sealing door and yesterday I did my first smoke with it after I had that gasket in place..

Man what a difference !!
The temp regulation with the little chimney on top is about 100 % better -
the inside temp is getting quite alot higher on the same volume gas settings..
I burn gas on a much lower level to get a nice blue smoke
and my wood chip box burns a lot longer and slower..

For Owners of one of these units - In my opion- it's Well worth the money!!

fingerlickin' 04-08-2012 12:45 AM

I have one of those cookers. I haven't used it since I got my egg though. I have put out some good food with it in the past. I've been thinking about giving it to a friend who has shown some interest in Q. If I do i'll probably do the gasket first. Thanks for the info.

ITBFQ 10-01-2012 03:12 PM

Does the gasket go on the inside of the door? I have an older similar looking Brinkmann that I want to seal up nice and tight. How's the fit around the hinges?

GARNAAL 02-11-2013 02:14 PM

I guess you can place the gasket either way -
on the inside of the door or,
on the ridge of the body of the smoker where the door meets it,
to seal the space between them, when you close the door..

Motley Q 02-11-2013 02:20 PM

If Masterforge or any other mfg of smokers really cared about the quality of their product,

They would make them already insulated at the doors.

It seems manufacturers haven't got a clue.

IamMadMan 02-17-2013 05:28 PM

Quote:

Originally Posted by Motley Q (Post 2363825)
If Masterforge or any other mfg of smokers really cared about the quality of their product,

They would make them already insulated at the doors.

It seems manufacturers haven't got a clue.

I'm sure they have a clue, but it interferes with their ability to make the most of their profit for as little cost as possible.

dwfisk 02-17-2013 06:29 PM

GARNAAL; There ain't no stupid questions for they folks on this forum and the odds are pretty good several have experienced the same kind of problem and found answers they are willing to share. Thanks for posting and adding to the knowledge pool.

Motley Q 02-17-2013 07:45 PM

Quote:

Originally Posted by IamMadMan (Post 2372134)
I'm sure they have a clue, but it interferes with their ability to make the most of their profit for as little cost as possible.

You sound like the mfg!

What does it cost to put a gasket around the door?

Next to nothing

Stop with the excuses.:cop:

GARNAAL 02-18-2013 11:20 AM

Quote:

Originally Posted by Motley Q (Post 2372315)
You sound like the mfg!

What does it cost to put a gasket around the door?

Next to nothing

Stop with the excuses.:cop:

------------------------
I do not think it's the cost of the gasket itself -
but the additional step in the Mfg process that adds $$

placing the heat resistant seal and then position the gasket and let it dry undisturbed before packaging the product consumes time ....
and process time == money...:mrgreen:


All times are GMT -5. The time now is 01:16 AM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
2003 -2012 BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.