The BBQ BRETHREN FORUMS.

The BBQ BRETHREN FORUMS. (http://www.bbq-brethren.com/forum/index.php)
-   Gravity Fed smokers and Grills (http://www.bbq-brethren.com/forum/forumdisplay.php?f=95)
-   -   Do you need WIFI on your temperature controller (http://www.bbq-brethren.com/forum/showthread.php?t=113733)

woodpelletsmoker 08-14-2011 07:40 PM

Do you need WIFI on your temperature controller
 
Find a similar temperature controller on thesmokering,
Controller plus 25 CFM blower is US$410.
My controller plus 50 CFM blower is US$128.

The differences are:
1.Its output is simply on or off. So it has three blowers of 5,10, 25 CFM for small middle and big pits.
Mine has P.I.D. output, One 50 CFM blower can fit all or most pits.
P.I.D. output is much more clever, it collects history data, depending on performance of past, present, and predicted future tendency to determine the speed of blower. Benefit is that temperature fluctuation is much less.

2.Mine has adjustable manual output. It is useful when searing. or grilling.

3.It has WIFI, you can read or control from your computer.

My question is that is WIFI a must, or are you will to pay for extra cost for WIFI.
Depending on replies here I will decide whether I will add WIFI or not.

woodpelletsmoker 08-14-2011 10:07 PM

How does PID works

It collects history data, speed of blower, and temperature of pit.
It considers history performance, present performance and predicted future performance to determine speed of blower.

Say you set pit temperature at 220 F.
When pit temperature is 180F, it will control blower running at peak speed,
When pit temperature reaches to 200F, blower may run at 50% of its normal speed.
When temperature reaches to 215F, blower may run at 10% of its normal speed
When temperature reaches to 219F, the blower may stop running.
Even then pit temperature will continue to rise.
When temperature reaches to 220F, the blower may begin to run again at 10% of normal speed.

Different pit may have different weighing factors of past, present and future, i.e. different value of P, I and D.
By trial and error, you will find best matching data of P,I.D, and your pit temperature fluctuation will keep within 1 F.

Many other controller, cheaper or much more expensive, their output is electrical relay or contacter. It simply turns on or off the blower.
Say you set pit temperature at 220F.
When pit temperature is 180F, the blower will run at its peak speed.
When pit temperatures to 200F, the blower will run at its peak speed.
When pit temperatures to 215F, the blower will run at its peak speed.
When pit temperatures to 219F, the blower STILL run at its peak speed.
When pit temperatures to 220F, the blower will STOP running.
But the pit temperature will CONTINUE to rise, it may rise to as high as 230F or even 240F, then it begins to drop
When pit temperature drops below 220F, the blower will run again at its peak speed.
But the pit temperature will CONTINUE to drop, it may drop to as low as 210F or even 200F, then it begins to rise.
Temperature fluctuation may be as high as 20F or even 40F.


All times are GMT -5. The time now is 12:47 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vBulletin Optimisation provided by vB Optimise v2.6.0 Beta 4 (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
2003 -2012 BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.