The BBQ BRETHREN FORUMS.

The BBQ BRETHREN FORUMS. (https://www.bbq-brethren.com/forum/index.php)
-   Q-talk (https://www.bbq-brethren.com/forum/forumdisplay.php?f=5)
-   -   Grinders + Buckboard bacon (https://www.bbq-brethren.com/forum/showthread.php?t=59467)

Mo-Dave 04-03-2009 01:58 PM

Grinders + Buckboard bacon
 
If this works you should see photos of the two grinders I now have, along with the Buckboard bacon I mentioned in a previous post. If the photos don't work you will just have to take my word that it happened. I have not had much luck posting pic lately and I wont try again on these, if it does not work, sorry.

Side by side comparison of a #32 and #22 grinder.
http://i37.photobucket.com/albums/e6...t/100_2328.jpg

This shows the bearings in the #32 and though you can't see it the #22 has a plastic sleeve instead of bearings. Well it looks like you can see a bit of the plastic in the smaller grinder.
http://i37.photobucket.com/albums/e6...t/100_2329.jpg

Business end of the two grinders.
http://i37.photobucket.com/albums/e6...t/100_2331.jpg

And lastly a couple photos of my first time try of the Buckboard bacon.
http://i37.photobucket.com/albums/e6...t/100_2313.jpg

Sorry no finished fried pic, could not get to the camera fast enough.:icon_wink
http://i37.photobucket.com/albums/e6...t/100_2315.jpg

I need to pick up a knife, stuffing blade and a larger size plate for the larger grinder. Going to mount this one to a 1/2 geared motor with a set of lovejoy couplings, my only concern is if it will be two slow as I mentioned before, the rpms are about 30/32, seems a little slow but we will see. Don't know what I will do with the #22 grinder it could become a present to one of my kids someday, heck everything I own with be a present to my kids someday.:wink:
Dave

Markbb 04-03-2009 02:05 PM

Nice set up....I'd be alittle concerned over the bearing being exposed like that..

Mo-Dave 04-03-2009 02:14 PM

Quote:

Originally Posted by Markbb (Post 893139)
Nice set up....I'd be alittle concerned over the bearing being exposed like that..

Yes not sure it that is normal or not but I guess I will find out. The up side is the bearings are 3 individual parts so they can be cleaned without a problem just have to lube them up before starting with some cooking oil or some lard would be my best guess.
Dave

millsy 04-03-2009 02:17 PM

bacon looks great.You guy's are given me to many ideas,I dont know where to start.

livens 04-03-2009 02:29 PM

Nice looking meat grinders :) I use a size smaller, clamp down hand crank style.

That bearing is a thrust bearing, and would be almost impossible to seal even if they inset it into the back. Its purpose is keep the auger turning smooth when you tighten the end up.

cowgirl 04-03-2009 04:56 PM

Good looking bacon and grinders Dave!

JimT 04-03-2009 05:19 PM

When I opened this thread, I was thinking grinder - the sandwich. Mmmmm, a buckboard bacon grinder!!!

Guess I was hungry.

JimT

Mo-Dave 04-04-2009 02:17 AM

Quote:

Originally Posted by JimT (Post 893241)
When I opened this thread, I was thinking grinder - the sandwich. Mmmmm, a buckboard bacon grinder!!!

Guess I was hungry.

JimT

Well why not? At work I got the idea to do some bacon welted lettuce, haven't had that since I was a kid.:grin:
Dave


All times are GMT -5. The time now is 04:03 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2003 -2012 © BBQ-Brethren Inc. All rights reserved. All Content and Flaming Pig Logo are registered and protected under U.S and International Copyright and Trademarks. Content Within this Website Is Property of BBQ Brethren Inc. Reproduction or alteration is strictly prohibited.